Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Veneer Hammer: an Iron Strip Set in a Wooden Head (Work, 1889)
Woody

Autor

Woody

8. listopad 2026NO
9
0
0
0
0

Veneer Hammer: an Iron Strip Set in a Wooden Head (Work, 1889)

The veneering hammer does not strike: it is drawn over glued veneer like a squeegee, pressing it down. David Adamson (1889) says it is hardly worth buying, as anyone can make one: a strip of iron 3 to 6 inches long set in a wooden head with a handle, its edge projecting, straight, and smoothly rounded. Shape and size do not matter much; it must be strong, the iron thick enough not to bend, and the edge smooth. Source: D. Adamson, 'Practical Veneering', Work, 5 October 1889, p. 453. Picture: his Fig. 1.
Początkujący
Unknown

Instrukcje

1

Read Adamson

"A strip of iron of, say, from 3 in. to 6 in. long and of any convenient width is firmly fixed between two pieces of wood, or in a groove cut in one piece to form the head. In this a handle is inserted. The precise shape and size of any part are quite immaterial, the principal points to be observed being strength and convenience."
2

Cut the iron strip

Cut a strip of iron 3 to 6 in. long and of any convenient width, thick enough not to bend when the hammer is pressed hard. Its thickness is not given (unknown). Ours: cut from iron plate with a hacksaw.

Materiały do tego kroku:

Płyta żelaznaPłyta żelazna1 strip 3-6 in.

Potrzebne narzędzia:

Piła do metaluPiła do metalu
Nieznane wymiaryNieznane wymiary
3

Make the head

Cut a groove in a block of wood and fix the strip firmly in it, with its edge projecting beyond the wood (or fix it between two pieces of wood). Fit a handle into the head. The wood, and how the strip and handle are fixed, are not given (unknown). Ours: a hardwood block, the groove sawn.

Materiały do tego kroku:

Klocek z drewna twardegoKlocek z drewna twardego1 head
Trzonek narzędziaTrzonek narzędzia1 sztuka
Nieznane złączeNieznane złącze1 sztuka

Potrzebne narzędzia:

Piła grzbietnicaPiła grzbietnica
4

Round the edge

File the projecting iron edge straight, smooth and rounded so it passes freely over the veneer, and slightly round off its lower corners so they do not damage the veneer. The smoother the edge, the easier the tool is to use.

Potrzebne narzędzia:

Pilniki (pilnik ręczny)Pilniki (pilnik ręczny)

Materiały

4

Wymagane narzędzia

4

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...