Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
Woody

Autor

Woody

4. listopad 2026NO
10
0
0
0
0

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)

A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle. Painted red inside and light green outside, lined in a lighter colour and black. Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
Średniozaawansowany
Unknown

Instrukcje

1

Make the hales

Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.

Materiały do tego kroku:

Deska jesionowaDeska jesionowa1 hales 3 ft 1 in x 1 5/8 x 1 1/2 in

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Strug ręcznyStrug ręczny
Strug kabłąkowyStrug kabłąkowy
2

Frame with oak cross-pieces

Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.

Materiały do tego kroku:

Deska z dębu białegoDeska z dębu białego1 sztuka
Kołek drewnianyKołek drewniany1 3/16 in pins

Potrzebne narzędzia:

Piła grzbietnicaPiła grzbietnica
Dłuto do gniazdDłuto do gniazd
Znacznik stolarskiZnacznik stolarski
Świder korbowy z wiertłemŚwider korbowy z wiertłem
Kątomierz nastawnyKątomierz nastawny
3

Fit the legs and stays

Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.

Materiały do tego kroku:

Deska z dębu białegoDeska z dębu białego1 legs 1 1/2 in square, stays
Śruba zamkowaŚruba zamkowa4 3 in

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Świder korbowy z wiertłemŚwider korbowy z wiertłem
Zestaw wkrętakówZestaw wkrętaków
4

Bottom and sides

Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 1/2 in bottom, 5/8 in sides
Farba olejnaFarba olejna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
Strug ręcznyStrug ręczny
Zestaw pędzliZestaw pędzli
5

Front board and ironwork

Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.

Materiały do tego kroku:

Deska sosnowaDeska sosnowa1 3/4 in front board
Gwoździe żelazneGwoździe żelazne1 1 1/2 in cut nails
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 7/8 in hoop iron
Wkręty do drewnaWkręty do drewna1 3/4 in round-headed
Farba olejnaFarba olejna1 sztuka

Potrzebne narzędzia:

Piła ręcznaPiła ręczna
MłotekMłotek
Zestaw wkrętakówZestaw wkrętaków
Zestaw pędzliZestaw pędzli
6

Make the wheel

Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.

Materiały do tego kroku:

Deska jesionowaDeska jesionowa1 axle and felloes
Deska z dębu białegoDeska z dębu białego1 spokes
Okrągły pręt żelaznyOkrągły pręt żelazny1 3/8 in pins
Kołek drewnianyKołek drewniany4 1/4 in
Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej1 3/4 x 1/8 in tyre

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Strug kabłąkowyStrug kabłąkowy
Świder korbowy z wiertłemŚwider korbowy z wiertłem
MłotekMłotek
7

Hang the wheel and paint

Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.

Materiały do tego kroku:

Płaskownik ze stali miękkiejPłaskownik ze stali miękkiej2 3/4 x 1/8 in irons
Wkręty do drewnaWkręty do drewna1 sztuka
Farba olejnaFarba olejna1 sztuka

Potrzebne narzędzia:

Zestaw wkrętakówZestaw wkrętaków
Zestaw pędzliZestaw pędzli

Materiały

10

Wymagane narzędzia

12

Według tego planu powstaje

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...