Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Laminated Rubber Mallet: A Rubber-and-Canvas Head Locked on a Flared Handle by an Internal Rib (Whisler, 1924)
Forge

Autor

Forge

13. listopad 2026NO
9
0
0
0
0

Laminated Rubber Mallet: A Rubber-and-Canvas Head Locked on a Flared Handle by an Internal Rib (Whisler, 1924)

Chauncy P. Whisler of Kenmore, Ohio, received US 1,501,827, dated 15 July 1924, for The Miller Rubber Company of Akron. It solves how to fix a handle in a head that is itself elastic. The rubber-and-fabric head has an eye that flares outwards, with a narrow rib at the handle side. The handle has a matching flared end, a groove for the rib and a shoulder. It is pushed right through the warm head from the outer face until the rib snaps into the groove. The flare stops the head flying off and the rib stops it sliding up the handle. We build the head from rubber sheet and canvas, ply by ply, as his "stepped conical eye". The sizes are ours.
Początkujący
About 2 days

Instrukcje

1

The stepped eye and the stretch at the rib

Wczytywanie notatnika Jupyter…
2

Read US 1,501,827

"When in position, the flared end 1a of the handle absolutely precludes the head from flying off when delivering blows and the rib and groove engagement prevents any inward displacement of the head."
3

Print the ply template

Full-size A4 template: the 110 x 60 mm ply and the hole circle for each of the 17 plies, largest at the outer face. Print at 100 %; its 50 mm bar must measure 50 mm.
Plik projektowyPDFCC0 - Free
4

Cut the plies

Cut 17 plies of 3 mm natural rubber sheet 110 x 60 mm and 14 of cotton canvas the same size. Glue each paper circle from the template in the middle of its ply, numbered 1 to 17, and cut the hole round it with a sharp craft knife, holding the blade upright. Cut the same hole in a canvas ply for each of plies 1 to 14.

Materiały do tego kroku:

Płyta z kauczuku naturalnegoPłyta z kauczuku naturalnego2 sztuk
Płótno brezentowe bawełnianePłótno brezentowe bawełniane1 sztuka

Potrzebne narzędzia:

Drukarka atramentowaDrukarka atramentowa
KlejKlej
Nóż introligatorskiNóż introligatorski
Kątownik nastawnyKątownik nastawny
5

Laminate the head

Brush contact cement on both faces to be joined, let it go touch-dry, and lay up the stack in order, ply 1 at the bottom: rubber, canvas, rubber, ... with the holes lined up over a 24 mm dowel through the middle, and plies 15, 16 and 17 rubber to rubber with no canvas. Press it between boards in clamps overnight. Trim the sides square with the knife and round the edges of the two striking faces slightly.

Materiały do tego kroku:

Klej kontaktowyKlej kontaktowy1 sztuka

Potrzebne narzędzia:

Kołki z twardego drewnaKołki z twardego drewna
Ścisk stolarski listwowyŚcisk stolarski listwowy
Nóż introligatorskiNóż introligatorski
Kątownik nastawnyKątownik nastawny
6

Turn the handle

Turn a hardwood handle 330 mm long. At its head end turn the flared part 2a as long as plies 1 to 15 are thick, 32 mm at the end tapering to 24; then the groove 2b, 20 mm across and as long as plies 16 and 17; then the shoulder 2c, 28 mm, to bear on the head's inner face; then the grip, 28 mm tapering to 26 at its end, so it can pass the eye. Check each diameter with the caliper against the plies.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Zestaw dłut tokarskich (HSS)Zestaw dłut tokarskich (HSS)
Suwmiarka cyfrowa 6 caliSuwmiarka cyfrowa 6 cali
Okulary ochronneOkulary ochronne
7

Fit the head

Warm the head for ten minutes in hot water and dry it. Push the grip end of the handle into the eye from the outer face (ply 1) and force it right through, the rib stretching over the grip and the shoulder, until the flared part seats in the eye and the rib snaps into the groove. Let it cool. Strike a board: the head must not move.

Potrzebne narzędzia:

WodaWoda
8

Troubleshooting

Rubber mallet troubleshooting.

Flow

Loading...
9

History and honest limits

**Chauncy P. Whisler** of Kenmore, Ohio, assignor to The Miller Rubber Company, US 1,501,827, dated 15 July 1924, filed 2 January 1924. He claimed "a mallet having a head of elastic material provided with an outwardly flaring handle-receiving eye provided with an annular internal rib adjacent the inner face of the head, and a handle having an outwardly flared end engaging said flared eye, and an annular groove engaged by said annular rib", and "a stepped conical eye". His head was moulded of rubber and fibrous material, as in Maranville and Dabney's application; ours is laminated from rubber sheet and canvas with contact cement. He gives no sizes; every size here is ours.

Materiały

4

Wymagane narzędzia

11

Pliki projektowe

1

Według tego planu powstaje

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...