Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Winding Sticks: a Pair of Parallel Mahogany Strips Planed Together (Work, 1889)
Woody

Autor

Woody

8. listopad 2026NO
8
0
0
0
0

Winding Sticks: a Pair of Parallel Mahogany Strips Planed Together (Work, 1889)

Two parallel wooden strips laid across a board to show twist (winding). Carpenters and joiners made their straightedges in pairs as winding strips: if two parallel strips still meet edge to edge when their edges and ends are swapped, three edges have been checked against each other and the strips are true. Straight-grained mahogany is used for strips under three feet. The two are planed together, then tried against each other and reversed until no difference shows. Source: J. H., 'Home-Made Tools', Work, 26 October 1889, pp. 499-500. Picture: Figs. 26-27.
Średniozaawansowany
Unknown (the stuff is left to stand for days or weeks first)

Instrukcje

1

Read the source

"Carpenters, joiners, pattern makers, and cabinet makers usually make their straightedges in pairs as 'winding strips;' and it is clear that if two winding strips are in the first place parallel, and then coincident when the positions of edges and ends are changed, there is obtained really the contact of three edges." (Work, 26 October 1889.)
2

Rough out and let stand

Rough out two strips of well-seasoned, straight-grained mahogany (for strips under three feet; long ones are made of yellow pine). Jack them over and let them stand for a few days or even weeks, because fresh-cut strips curve and warp. Length, width and thickness are not given (unknown).

Materiały do tego kroku:

Listwa z drewna twardegoListwa z drewna twardego2 mahogany strips

Potrzebne narzędzia:

Strug ręcznyStrug ręczny
Nieznane wymiaryNieznane wymiary
3

Plane them together

Plane both to gauged thickness and width and square the ends. Screw the two side by side, then finish the edges together with a trying plane sharpened keenly and set very fine. Gauge to width with a fine-toothed gauge, check them parallel with calipers, and keep the edges square to the faces with a try square.

Potrzebne narzędzia:

Wkręty do drewnaWkręty do drewna
Strug ręcznyStrug ręczny
Znacznik stolarskiZnacznik stolarski
SuwmiarkaSuwmiarka
Kątownik stolarskiKątownik stolarski
4

Test the edges

To test an edge without a straightedge, lay the strip on a board, scribe a fine line along the edge, turn the strip over and bring the opposite edge to the line: any error shows at twice its size. Plane off the high parts, still checking with calipers and square.

Potrzebne narzędzia:

Deska z drewna liściastegoDeska z drewna liściastego
Nóż traserskiNóż traserski
Strug ręcznyStrug ręczny
SuwmiarkaSuwmiarka
Kątownik stolarskiKątownik stolarski
5

Unfasten and try them against each other

Take the screws out. Lay the strips edge to edge by opposite edges in turn, then change ends and try the opposite edges again, correcting with the trying plane until no difference shows (woodworkers test by chalking the edges and laying them together). Most of the work should already have been done while they were joined.

Potrzebne narzędzia:

Kreda do znakowaniaKreda do znakowania
Strug ręcznyStrug ręczny
SuwmiarkaSuwmiarka
Kątownik stolarskiKątownik stolarski
6

Varnish the faces

Protect the broad faces and the ends with shellac varnish, but not the edges, which are chalked in use. Chalking wears the edges hollow and wood always warps a little, so re-correct winding strips every few months, and keep them for testing winding only.

Materiały do tego kroku:

Politura szelakowaPolitura szelakowa1 faces and ends

Materiały

2

Wymagane narzędzia

9

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...