SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Woven Wire Screen Cloth: Hardened Crimped Steel Rods Locked by Driven Straight Rods (Robins, US 2,154,530, 1939)
Charlie

Autor

Charlie

31. październik 2026DE
0
0
0
0
0

Woven Wire Screen Cloth: Hardened Crimped Steel Rods Locked by Driven Straight Rods (Robins, US 2,154,530, 1939)

Screen cloth for gravel and stone wears out fast unless the steel is hard, but hard steel cracks when it is bent in weaving. Robins crimps the rods first, hardens them, and lays them up in layers without bending; straight hardened rods driven in endwise lock the whole panel under spring pressure. Result: coarse screen cloth, openings 5/8 in and up, hardened to as much as 60 Rockwell C; it lasted about twice as long. Source: Robins, US 2,154,530 (1939). He names only steel; a high-carbon steel is ours, since only a hardenable steel reaches 60 Rockwell C. Not given: crimp pitch, hardening heat and quench. Picture drawn by Youblob.
Zaawansowany
Factory process

Instrukcje

1

Crimp the rods

Cut steel rods, about 3/16 in diameter or more, to length and press-crimp three sets of them between dies. Keep a fourth set straight (no more than a quarter of all rods).

Materiały do tego kroku:

Walcówka ze stali wysokowęglowejWalcówka ze stali wysokowęglowej1 as required

Potrzebne narzędzia:

Prasa do tłoczeniaPrasa do tłoczenia
2

Harden all the rods

Heat-harden the crimped and the straight rods before assembly; crimping first spares the dies. Robins reached 60 Rockwell C. Heat and quench: not given.

Potrzebne narzędzia:

Piec muflowyPiec muflowy
Kadź hartowniczaKadź hartownicza
3

Lay up three crimped sets

Lay crimped set 1 in parallel on a table; lay set 3 across it, bends in register; lay set 2 parallel to set 1 on top, its bends opposite. Openings about 5/8 in or more.

Potrzebne narzędzia:

Stół warsztatowyStół warsztatowy
4

Drive in the straight rods

Drive the straight rods endwise, above set 2 and below set 1, alternating with set 3. They lock the panel by spring pressure without bending any rod for good; pulled out again, worn rods can be replaced.

Potrzebne narzędzia:

Młot dwuręcznyMłot dwuręczny

Materiały

1

Wymagane narzędzia

5

Powiązane blueprinty

Te blueprinty dzielą się wiedzą — technikami, materiałami lub zasadami

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...