Сотрудничество
ИСКУССТВО
КРАСОТА И ЗДОРОВЬЕ
РЕМЕСЛО
КУЛЬТУРА И ИСТОРИЯ
РАЗВЛЕЧЕНИЯ
ЭКОЛОГИЯ
ЕДА И НАПИТКИ
ОБРАТНАЯ ИНЖЕНЕРИЯ
НАУКИ
СПОРТ
ТЕХНОЛОГИИ
НОСИМЫЕ УСТРОЙСТВА
Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)
Forge

Создано

Forge

4. ноябрь 2026NO
14
0
0
0
0

Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)

A shop brazing and tempering torch: a wall-hung pipe tank of gasoline or kerosene pumped up with a bicycle pump, feeding a 1/8 in pipe whose end is coiled round a short 1 in pipe; the flame heats the coil, the oil turns to gas, and it blasts out through a pinhole cap. Two burners on a tee give a bigger heat. Source: Popular Mechanics Shop Notes for 1909, pp. 861-862. Picture: the article's drawing.
Средний
Unknown

Инструкции

1

Make the tank

Cap both ends of a 2 in pipe 20 in long. Drill three holes in the top cap: one for the rubber tube from a bicycle pump, one for a steam gauge, and one with a screw plug for filling with fuel oil.

Материалы для этого шага:

Стальная труба (толстостенная, с резьбовыми концами)Стальная труба (толстостенная, с резьбовыми концами)1 2 in x 20 in
Резьбовой трубный фитингРезьбовой трубный фитинг3 two caps, plug
МанометрМанометр1 штука
Резиновая трубкаРезиновая трубка1 штука

Необходимые инструменты:

Ручная дрельРучная дрель
Набор метчиков и плашекНабор метчиков и плашек
Трубный ключТрубный ключ
Напольный велосипедный насосНапольный велосипедный насос
2

Coil the burner

Drill the bottom cap and connect a 1/8 in pipe D, any length, with a globe valve in it to set and shut off the oil. Fill the last 10 in of the pipe with lead, coil it round a 1 in pipe F 6 in long, and turn the end out to take two elbows and a short nipple; then melt the lead out. Drill a small hole in the centre of a 1/8 in cap and fit it on the end (E) so the hole lines up with the centre of pipe F.

Материалы для этого шага:

Стальная труба (толстостенная, с резьбовыми концами)Стальная труба (толстостенная, с резьбовыми концами)1 1/8 in, and 1 in x 6 in
Резьбовой трубный фитингРезьбовой трубный фитинг4 two elbows, nipple, 1/8 in cap
ВентильВентиль1 штука

Необходимые инструменты:

СвинецСвинец
Дырчатая шумовкаДырчатая шумовка
ГорнГорн
Ручная дрельРучная дрель
Трубный ключТрубный ключ
3

Start the burner

Hang a little cup holding three or four teaspoonfuls of oil just below the coil and light it to heat the coil; then pump up the tank and open the globe valve. For more heat connect two burners on a tee so their blasts meet.

Необходимые инструменты:

КеросинКеросин
Напольный велосипедный насосНапольный велосипедный насос

Материалы

5

Требуемые инструменты

8

CC0 Общественное достояние

Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.

Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.

Обсуждение

(0)

Войти чтобы присоединиться к обсуждению

Загрузка комментариев...