ИСКУССТВО
КРАСОТА И ЗДОРОВЬЕ
РЕМЕСЛО
КУЛЬТУРА И ИСТОРИЯ
РАЗВЛЕЧЕНИЯ
ЭКОЛОГИЯ
ЕДА И НАПИТКИ
ОБРАТНАЯ ИНЖЕНЕРИЯ
НАУКИ
СПОРТ
ТЕХНОЛОГИИ
НОСИМЫЕ УСТРОЙСТВА
Forged Hunting Axe (Hatchet)
Forge

Создано

Forge

11. октябрь 2026NO
30
0
0
0
0

Forged Hunting Axe (Hatchet)

A small one-handed axe forged from a 7/8 × 2-inch bar of good tool steel, best made by two people; a 6¾-inch bar gives two heads. The eye, about 9/16 × 1½ inches, is punched at a yellow heat with an eye punch and opened with drifts, the blade drawn out to a 3-inch edge and the head cut to length. The axe is annealed in lime or ashes, ground and buffed, then hardened from the hardening heat in tepid water and tempered by two hot iron bars laid on either side at the centre: dark purple for the blade, blue for the head.
Продвинутый
4–6 hours

Инструкции

1

Mark and punch the eye

Mark the stock with chisel and centre punch. At a yellow heat, punch the eye with the narrow edge of the punch toward the blade; lift the punch after each blow to check it runs straight and to let it cool; a little fine coal in the hole stops it sticking. Punch nearly through, then finish from the other side.

Материалы для этого шага:

Полоса из инструментальной сталиПолоса из инструментальной стали1 штука

Необходимые инструменты:

КернерКернер
Кузнечный горнКузнечный горн
НаковальняНаковальня
Горячий пробойникГорячий пробойник
КувалдаКувалда
Кузнечные клещиКузнечные клещи
2

Drift and draw out

Drive in a tool-steel drift, hammer the bulges down to the bar's size and smooth with a flatter; take the drift out before each reheat. Use two drifts, the first 3/8 inch narrower. Draw out the blade, driving the drift back in as the eye stretches so no cold shut forms.

Необходимые инструменты:

Оправка для расширения отверстияОправка для расширения отверстия
Гладилка кузнечнаяГладилка кузнечная
Хвостовой молотХвостовой молот
3

Shape and trim

Shape the blade with a heavy hammer and flatter and form its edge. Cut the head from the bar, draw it to size, cut it to length, then trim the blade to shape.

Необходимые инструменты:

Кузнечный молотКузнечный молот
Гладилка кузнечнаяГладилка кузнечная
Горячее зубило (кузнечная рубка)Горячее зубило (кузнечная рубка)
4

Anneal and grind

Heat to a full red and anneal in lime or ashes. When cold, grind on an emery wheel and finish on a buffing wheel.

Необходимые инструменты:

Кузнечный горнКузнечный горн
Настольный точильный станокНастольный точильный станок
5

Harden and temper

Heat very slowly to the hardening heat and cool in tepid water. Draw the temper with two hot iron bars laid on either side at the centre; when the blade is dark purple and the head blue, cool quickly in water.

Необходимые инструменты:

Кузнечный горнКузнечный горн
Закалочная бадьяЗакалочная бадья
Кузнечные клещиКузнечные клещи
6

Handle

Shave the handle stock to fit the eye tightly, drive the head on, saw a kerf in the handle's top and drive a glued hardwood wedge into it. Trim flush and oil the handle.

Материалы для этого шага:

Заготовка рукояти из твёрдой древесиныЗаготовка рукояти из твёрдой древесины1 штука
Клин из твёрдой древесиныКлин из твёрдой древесины1 штука
Льняное маслоЛьняное масло10 мл

Необходимые инструменты:

СтругСтруг
Двуручная поперечная пилаДвуручная поперечная пила
Слесарные тискиСлесарные тиски

Материалы

4

Требуемые инструменты

16

По этому чертежу делают

Связанные чертежи

Эти чертежи делятся знаниями — техники, материалы или принципы

CC0 Общественное достояние

Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.

Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.

Обсуждение

(0)

Войти чтобы присоединиться к обсуждению

Загрузка комментариев...