ИСКУССТВО
КРАСОТА И ЗДОРОВЬЕ
РЕМЕСЛО
КУЛЬТУРА И ИСТОРИЯ
РАЗВЛЕЧЕНИЯ
ЭКОЛОГИЯ
ЕДА И НАПИТКИ
ЗЕЛЁНОЕ БУДУЩЕЕ
ОБРАТНАЯ ИНЖЕНЕРИЯ
ШКОЛЬНЫЕ ПРОЕКТЫ
НАУКИ
СПОРТ
ТЕХНОЛОГИИ
НОСИМЫЕ УСТРОЙСТВА
Building a Travois — Pole-Frame Load Carrier
Woody

Создано

Woody

25. май 2026NO
12
0
0
1
0

Building a Travois — Pole-Frame Load Carrier

The travois is a simple A-frame transport device consisting of two long poles joined at one end and spread apart at the other, with a platform or netting between them for carrying loads. It is the oldest known land transport technology, predating the wheel by thousands of years. Before horses arrived in the Americas, Plains peoples used dog-pulled travois to move camp — the poles doubled as tipi frame poles. A human-pulled travois can transport 40 to 60 kg of cargo that would be impossible to carry on the back alone. The trailing pole ends act as skids, sliding over grass, snow, and rough ground. The design is so simple and effective that it remained in use alongside wheeled transport well into the 19th century for terrain where wheels cannot operate.
Начинающий
1-2 hours

Инструкции

1

Select Two Long, Straight Poles

Select two straight, strong poles 3 to 4 metres long and 5 to 8 cm in diameter. Ash, spruce, and pine are all suitable — the poles must be strong enough to bear the load without snapping, and flexible enough not to shatter on rough ground. Green (freshly cut) wood is preferred because it is more resilient than seasoned wood.

Материалы для этого шага:

Hardwood SaplingHardwood Sapling2 штук
2

Strip Bark and Side Branches

Strip all bark and remove every side branch from both poles. Bark retains moisture and attracts insects, and protruding branch stubs snag on undergrowth and injure the person pulling the travois. Use a flint scraper or knife to shave the branch stubs flush with the pole surface.
3

Lash the Poles Together at the Narrow End

Lay the poles side by side and lash them together at the narrow (thinner) end with strong cordage, leaving 30 to 40 cm of pole extending beyond the lashing. Use a diagonal or shear lashing, wrapping tightly at least 8 times around both poles with frapping turns between to cinch the binding tight. This joint is the primary stress point — it must not slip.

Материалы для этого шага:

CordageCordage1 штука
4

Spread the Butt Ends Apart

Spread the butt (thicker) ends apart to form an A-frame, with the wide end 60 to 80 cm apart. The joined narrow end points forward (toward the puller) and the spread butt ends trail behind on the ground. The angle between the poles determines the platform width — too narrow and cargo falls off, too wide and the frame flexes excessively.
5

Lash Crossbars Between the Poles

Lash two or three crossbars (straight sticks 2 to 3 cm in diameter) between the poles perpendicular to the main poles. Start the first crossbar approximately 1 metre from the joined end and space additional crossbars 30 to 40 cm apart. Use square lashings at each junction — wrap around both the crossbar and pole in alternating directions, then frap between to tighten.

Материалы для этого шага:

CordageCordage1 штука
6

Weave a Cargo Platform

Weave a platform of smaller sticks, rawhide strips, or rope netting between the crossbars to hold cargo. If using sticks, lay them across the crossbars close together and lash each end. If using rawhide strips or rope, weave a net in a simple grid pattern tied to the crossbars and main poles. The platform must support the load without sagging through to the ground.
7

Add a Cargo Liner (Optional)

Lash a hide or large piece of bark over the platform to contain loose items like dried food, tools, or bedding. Without a liner, small items fall through gaps in the platform. Tie the liner at its corners and edges to the crossbars so it does not shift during transport.
8

Attach a Pulling Harness

Attach a chest harness or shoulder straps of rawhide or braided cord near the joined end of the poles. The harness should distribute the pulling force across the chest and shoulders, not concentrate it on the hands. A simple breast strap tied to each pole just behind the junction works effectively — the puller leans into it with their body weight.

Материалы для этого шага:

CordageCordage1 штука
9

Load the Cargo

Load cargo onto the platform, keeping the weight centred between the crossbars and balanced equally on both sides. Heavy items go at the bottom, close to the ground, to keep the centre of gravity low. A travois that is top-heavy or unevenly loaded will tip sideways on uneven ground.
10

Pull the Travois

Lean forward into the harness and drag the travois behind you. The butt ends of the poles trail on the ground, acting as skids. On smooth grass or snow, a loaded travois slides easily. On rough terrain, lift the front end slightly to clear obstacles. The trailing poles flex over bumps rather than jolting, which is why the travois works on terrain that defeats wheeled carts.

Материалы

2

Материалы из связанных чертежей

Required Equipment

Equipment this kind of build typically needs — buy from any maker below.

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Recommended for this build

Products makers often use with builds like this one.

Flint KnifeUsed together and in similar builds
HammerstoneUsed together and in similar builds
Bone AwlUsed together and in similar builds
Birch Bark SheetsUsed together and in similar builds
Sandstone (Abrasive)Used together and in similar builds
Flat Stone SlabUsed together and in similar builds
Animal Bones (cleaned, degreased)Used together and in similar builds
Animal Fat (Tallow)Used together and in similar builds

Связанные чертежи

Эти чертежи делятся знаниями — техники, материалы или принципы

Making Rope from Inner Bark — Twisted Bast Fibre Cordageот Bob
Making Rawhide Cord — Strong Binding from Animal Skinот Tex
Building a Wattle Fence — Woven Wood Panel Constructionот Woody

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Building a Bark Canoe — Birch Bark Frame Watercraftwoodworking
Building a Pit House — Semi-Subterranean Earth Lodge Dwellingwoodworking
Building a Reed Bundle Raft — Buoyant Watercraft from Wetland Plantswoodworking
Building a Box Bellows — The Breath That Makes Metal Obey Firewoodworking
Building a Wattle-and-Daub Wall — The Universal Prehistoric Construction Techniquewoodworking
Building a Prehistoric Coracle — A One-Person Bowl Boat from Woven Branches and Animal Hidewoodworking

CC0 Общественное достояние

Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.

Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.

Обсуждение

(0)

Войти чтобы присоединиться к обсуждению

Загрузка комментариев...