Reading a Temperature Sensor — SIK Circuit 7

Read temperature from a TMP36 sensor and display Celsius and Fahrenheit readings on the Serial Monitor. Your introduction to serial communication and real-world data.

Инструкции

Parts & Introduction

The TMP36 is an analog temperature sensor that outputs a voltage proportional to temperature. You'll learn to use the Serial Monitor to display real-time readings — an essential debugging tool.

Parts Needed

1x Arduino Uno + USB cable
1x Breadboard
1x TMP36 Temperature Sensor
5x Jumper Wires

Warning: The TMP36 looks similar to the transistor. Look for "TMP" in tiny letters and a triangle logo. The transistor has "222" printed on it. Inserting the wrong component can damage it!

Hardware Hookup

Wiring Instructions

With the TMP36 flat side facing you and pins pointing down, the pins are (left to right): 5V, Signal, GND.

Connect the left pin to 5V.
Connect the middle pin (signal) to Analog Pin A0.
Connect the right pin to GND.

That's it — just 3 wires! The TMP36 can only be connected in one direction. Double-check before powering on.

Arduino Code

Open the Arduino IDE and upload the following sketch to your Arduino board.

temperature_sensor.inoarduino

/*
SparkFun Inventor's Kit
Example sketch 07 — TEMPERATURE SENSOR

Use the serial monitor to read temperature from a TMP36 sensor.

Hardware connections:
  TMP36 (flat side, pins down, left to right): 5V, SIGNAL, GND
  Connect 5V pin to 5V, SIGNAL pin to analog pin 0, GND pin to GND.

This code is completely free for any use.
*/

const int temperaturePin = 0;

void setup()
{
  Serial.begin(9600);
}

void loop()
{
  float voltage, degreesC, degreesF;

  voltage = getVoltage(temperaturePin);

  degreesC = (voltage - 0.5) * 100.0;
  degreesF = degreesC * (9.0/5.0) + 32.0;

  Serial.print("voltage: ");
  Serial.print(voltage);
  Serial.print("  deg C: ");
  Serial.print(degreesC);
  Serial.print("  deg F: ");
  Serial.println(degreesF);

  delay(1000);
}

float getVoltage(int pin)
{
  return (analogRead(pin) * 0.004882814);
  // Converts 0-1023 to 0.0-5.0 volts
}

Test & Experiment

What You Should See

Open the Serial Monitor (magnifying glass icon in Arduino IDE, or Ctrl+Shift+M). You'll see lines updating once per second:

voltage: 0.73  deg C: 23.24  deg F: 73.84

Troubleshooting

Nothing happens: Open the Serial Monitor! The output goes there, not to the LEDs.
Gibberish text: Set the Serial Monitor baud rate dropdown to 9600.
Temperature unchanged: Pinch the sensor with your fingers to warm it up, or apply ice to cool it down.

Experiments to Try

Add an LED that turns on above a temperature threshold (like a heat warning).
Log data over time to see temperature trends.
Combine with the LCD (Circuit 15) to display temperature without a computer.

Материалы

•SparkFun Inventor's Kit - V3.2 - 1 kitNOK 999.20
Просмотр
•Arduino Uno R3 - 1 pieceЗаполнитель
Просмотр
•Breadboard - 1 pieceЗаполнитель
Просмотр
•TMP36 Temperature Sensor - 1 pieceЗаполнитель
Просмотр
•Jumper Wires - 5 piecessNOK 39.20
Просмотр

Требуемые инструменты

Computer with Arduino IDE

CC0 Общественное достояние

Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.

Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.

Обсуждение

(0)

Войти чтобы присоединиться к обсуждению

Загрузка комментариев...