ИСКУССТВО
КРАСОТА И ЗДОРОВЬЕ
РЕМЕСЛО
КУЛЬТУРА И ИСТОРИЯ
РАЗВЛЕЧЕНИЯ
ЭКОЛОГИЯ
ЕДА И НАПИТКИ
ОБРАТНАЯ ИНЖЕНЕРИЯ
НАУКИ
СПОРТ
ТЕХНОЛОГИИ
НОСИМЫЕ УСТРОЙСТВА

Youblob (drawn diagram, draw_corkscrew.py) · CC0
The Button Corkscrew: A Helix That Grips and a Disc That Stops It
A cork is squeezed into a bottle neck so hard that pulling it out by a simple worm takes a strong arm — and a worm driven too far pierces the cork and pushes crumbs into the wine. Samuel Henshall, an English clergyman, took out British patent No. 2061 on 24 August 1795 for a corkscrew with a button: a concave disc fixed between the worm and the shank. The button stops the worm once it is deep enough, and turning on past that point twists the whole cork in the neck, breaking its hold on the glass before it is pulled. Matthew Boulton's works in Birmingham made it.
This rung works out the worm's turns and grip and the force a pull needs, and makes and tests a button corkscrew.
Начинающий
About 2 hours
Инструкции
1
1
Worm pitch, grip and pulling force
Worm pitch, grip and pulling force
Загрузка блокнота Jupyter…
2
2
The helix underneath it
The helix underneath it
A corkscrew worm is a helix with nothing inside it. The embedded blueprint shows the helix as a ramp wrapped round a cylinder.
3
3
Make a worm and a button
Make a worm and a button
Wind 2 mm spring steel wire round a 6 mm rod held in a vice, five turns at an 8 mm pitch — set the pitch by winding over a spacer strip. Grind the free end to a point on the outside of the helix so it follows the helix, not the centre. Leave a straight tail as the shank.
For the button, drill a 20 mm steel washer to fit the shank and file its underside slightly concave with abrasive paper wrapped round a rod. Slide it down to where the worm starts and solder it in place. Fit a wooden handle across the top of the shank.
Материалы для этого шага:
Пружинная стальная проволока1 штука
Плоская шайба1 штука
Шканты из твёрдой древесины1 штука
Оловянно-свинцовый припой1 штукаНеобходимые инструменты:
Слесарные тиски
Аккумуляторная дрель
Набор свёрл
Набор наждачной бумаги
Паяльник
Кожаные рабочие перчатки
Прозрачные защитные очки4
4
Measure the pull, with and without the twist
Measure the pull, with and without the twist
Recork several empty wine bottles with new corks of the same kind, using a hand corker, and let them stand a day.
On the first, drive the worm in until the button touches, stop, and pull straight up with a spring scale hooked to the handle: read the peak force. On the next, drive it in until the button touches, then turn two more turns so the cork rotates in the neck, and pull again. Compare the peak forces. Compare also with a commercial corkscrew.
Материалы для этого шага:
Пробки6 штук
Набор для укупорки винных бутылок1 штука
Штопор1 штукаНеобходимые инструменты:
Динамометр (пружинные весы)5
5
A cork that will not come out cleanly
A cork that will not come out cleanly
Cork removal problems.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**Samuel Henshall** was granted **British patent No. 2061** on 24 August 1795 — the first patent for a corkscrew. Matthew Boulton made Henshall's corkscrews at Soho, Birmingham, marked "Obstando Promoves". Later designs added threads, levers and wings to take the effort out of the pull.
**Honest limits.** The cork pressure and friction in the notebook are illustrative; measure your own pulls. The patent itself is not in the patent databases used for this programme; its details here come from museum and patent-office sources.
Материалы
7- 1 штукаЗаполнитель
- 1 штукаЗаполнитель
- 1 штукаЗаполнитель
- 1 штукаЗаполнитель
- 6 штукЗаполнитель
- Заполнитель
- Штопор10% комиссия1 штукаЗаполнитель
Требуемые инструменты
8- Заполнитель
- 1 vendor sell this, none ship to you yetЗаполнитель
- Заполнитель
- Заполнитель
- Заполнитель
- Заполнитель
- Заполнитель
Связанные чертежи
Эти чертежи делятся знаниями — техники, материалы или принципы
CC0 Общественное достояние
Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.
Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.


