ИСКУССТВО
КРАСОТА И ЗДОРОВЬЕ
РЕМЕСЛО
КУЛЬТУРА И ИСТОРИЯ
РАЗВЛЕЧЕНИЯ
ЭКОЛОГИЯ
ЕДА И НАПИТКИ
ОБРАТНАЯ ИНЖЕНЕРИЯ
НАУКИ
СПОРТ
ТЕХНОЛОГИИ
НОСИМЫЕ УСТРОЙСТВА
The Grain Auger: Archimedes' Screw Spun Fast in a Tube
Martin

Создано

Martin

27. сентябрь 2026NO
31
0
0
0
0

The Grain Auger: Archimedes' Screw Spun Fast in a Tube

Archimedes' screw lifts water slowly by trapping it between turns of a spiral. Close the spiral in a tight tube and spin it fast, and it moves dry grain instead: the flights push the grain along and the tube keeps it from turning with them. The auger fills bins, empties combine tanks and loads trucks, at any angle from flat to steep, with nothing but a shaft and a motor. It is a sibling of the bucket elevator: the elevator lifts straight up in buckets and needs a tower; the auger lifts at a slant in a single tube and goes where it is carried. This rung works out an auger's theoretical delivery and why its fill factor must be measured, and builds a clear-tube auger to measure it at three angles.
Начинающий
About 4 hours

Инструкции

1

Delivery, fill factor and power

Загрузка блокнота Jupyter…
2

The water sibling

The same spiral lifts water when turned slowly in an open trough. The embedded blueprint builds one; compare how each holds its load.
3

Build a clear-tube auger

3D-print screw flights 40 mm across with a 40 mm pitch, in 150 mm sections with an 8 mm bore, and thread them onto an 8 mm threaded rod locked with nuts. Slide the screw into a clear acrylic tube with a 42 mm bore. Cut an intake window at the bottom and a discharge hole at the top. Mount the tube on a plywood stand that can be set at 0, 20 and 40 degrees, with the rod running in skateboard bearings at each end. Drive the top end from a geared DC motor on an adjustable supply. Keep your fingers, hair and sleeves clear of the intake window while it turns.

Материалы для этого шага:

Акриловая труба (прозрачная)Акриловая труба (прозрачная)1 штука
Шпилька резьбоваяШпилька резьбовая1 штука
ШарикоподшипникШарикоподшипник2 штук
Лист фанерыЛист фанеры1 штука
Мотор-редуктор постоянного токаМотор-редуктор постоянного тока1 штука
Сушёная чечевицаСушёная чечевица3 kilogram

Необходимые инструменты:

3D-принтер FDM3D-принтер FDM
Филамент PETGФиламент PETG
Источник питания постоянного токаИсточник питания постоянного тока
Аккумуляторная дрельАккумуляторная дрель
Набор свёрлНабор свёрл
Разводной ключРазводной ключ
ТранспортирТранспортир
Прозрачные защитные очкиПрозрачные защитные очки
4

Measure the fill factor

Keep the intake window buried in a tray of lentils. At each angle and at two motor speeds, run for 30 seconds, catch the discharge, weigh it, and read the shaft speed with the tachometer. Work out the theoretical delivery from the notebook's formula using your flight diameter, rod diameter and pitch, and the lentils' bulk density (weigh a measured jug full). The fill factor is measured delivery divided by theoretical. Tabulate it: it is highest flat and falls as the tube is tipped up, because more lentils slip back over the flights.

Необходимые инструменты:

Цифровой тахометрЦифровой тахометр
СекундомерСекундомер
Цифровые кухонные весыЦифровые кухонные весы
Мерный кувшинМерный кувшин
ВедроВедро
5

An auger that is not moving the grain

Grain auger faults, from the first to check.

Flow

Loading...
6

Context and honest limits

The screw conveyor is old; the portable farm auger in a tube is the form that moves most grain on farms today, from combine unloading augers to bin-filling augers. **Honest limits.** The notebook's theoretical delivery assumes a full tube moving one pitch per turn — no auger does this, which is why the bench test measures the fill factor. An auger damages some grain by rubbing, more at high speed and with fragile crops. And the exposed intake is one of the most common causes of serious injury on farms: guards stay on.

Материалы

6

Требуемые инструменты

13

CC0 Общественное достояние

Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.

Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.

Обсуждение

(0)

Войти чтобы присоединиться к обсуждению

Загрузка комментариев...