ИСКУССТВО
КРАСОТА И ЗДОРОВЬЕ
РЕМЕСЛО
КУЛЬТУРА И ИСТОРИЯ
РАЗВЛЕЧЕНИЯ
ЭКОЛОГИЯ
ЕДА И НАПИТКИ
ОБРАТНАЯ ИНЖЕНЕРИЯ
НАУКИ
СПОРТ
ТЕХНОЛОГИИ
НОСИМЫЕ УСТРОЙСТВА
The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles
Woody

Создано

Woody

6. октябрь 2026NO
28
0
0
0
0

The Sheet-of-Water Fountain Brush: Tapered Slots Part the Bristles

Water dribbled onto the back of a brush stays in the bristles and never reaches the surface being washed. Frank L. Brinn of Milwaukee received US 840,604, patented 8 January 1907, for a fountain brush in which "the fluid may be delivered to the longitudinal central portion of the brush in a sheet, which when the fluid is turned on at full head will serve to separate the bristles and flush the surface to be washed": slots through the block narrow toward the bristles, fed from a cylinder on top through a tubular handle, with a cup on the handle to catch what runs down. This rung works out how the taper speeds the sheet, then cuts the slots in a scrub brush, plumbs it and compares full flow with throttled flow.
Средний
About 4 hours

Инструкции

1

Sheet speed from the slot

Загрузка блокнота Jupyter…
2

Water through a brush's back before it

The embedded blueprint jets or soaks water through openings in a brush's back. Brinn shapes the openings into tapered slots so the water leaves as a sheet.
3

Read US 840,604

"By opening the valve at 3 to its full capacity a sheet of water will be discharged which will separate the bristles and effectively flush the surface to be washed, whether the bristles are in contact with such surface or not. By partially closing the valve at 3 the sheets of water escaping through the openings 18 are broken up by the bristles, and the water thus becomes distributed throughout the brush."
4

Cut the slots

On the scrub brush's top mark two slots 60 × 8 mm, 90 mm apart on the centre line. Drill a row of holes in each and cut it through with the coping saw.

Материалы для этого шага:

Жёсткая щёткаЖёсткая щётка1 штука

Необходимые инструменты:

Слесарные тискиСлесарные тиски
Аккумуляторная дрельАккумуляторная дрель
Набор свёрлНабор свёрл
Лобзиковая пилаЛобзиковая пила
Перманентный маркерПерманентный маркер
ЛинейкаЛинейка
5

Taper the slots

Pare each slot with chisels so its long sides close to about 1.5 mm at the bristle face and its ends open out to 70 mm. Trim the bristles along the slot line.

Необходимые инструменты:

Набор стамесок по деревуНабор стамесок по дереву
МолотокМолоток
Цифровой штангенциркуль 6 дюймовЦифровой штангенциркуль 6 дюймов
Макетный ножМакетный нож
6

Make the manifold

Cut 160 mm of 22 mm copper tube and cap both ends with fittings. File a 4 mm slot along its underside over both brush slots. Fit a tee in its middle for the handle.

Материалы для этого шага:

Медная трубаМедная труба1 штука
Латунные фитингиЛатунные фитинги1 штука

Необходимые инструменты:

ТруборезТруборез
Напильники (ручной напильник)Напильники (ручной напильник)
Разводной ключРазводной ключ
7

Seat the manifold

Bed the manifold on the brush in silicone over a rubber gasket and strap it down with an aluminium strip and four wood screws.

Материалы для этого шага:

Силиконовый герметикСиликоновый герметик1 штука
Резиновый листРезиновый лист1 штука
Алюминиевый листАлюминиевый лист1 штука
Шуруп по дереву #8 x 1"Шуруп по дереву #8 x 1"1 штука

Необходимые инструменты:

Ножницы по металлуНожницы по металлу
Набор отвёртокНабор отвёрток
Макетный ножМакетный нож
8

Handle, valve and drip cup

Fit 1.2 m of 15 mm copper tube to the tee, with a ball valve and hose connector at its top. Slide a small tin can, holed and sealed with silicone, onto the handle as a drip cup, and fit a short copper spout low on its side.

Материалы для этого шага:

Медная трубаМедная труба1 штука
Шаровой кранШаровой кран1 штука
Латунные фитингиЛатунные фитинги1 штука
Уплотнительная лента ПТФЭ для резьбыУплотнительная лента ПТФЭ для резьбы1 штука
Жестяная банкаЖестяная банка1 штука
Силиконовый герметикСиликоновый герметик1 штука

Необходимые инструменты:

ТруборезТруборез
Разводной ключРазводной ключ
Аккумуляторная дрельАккумуляторная дрель
Набор свёрлНабор свёрл
9

The patent drawing

US 840,604 drawing sheet, public domain (expired patent).
Шаг 9 - Image 1
10

Full flow against throttled

Connect the garden hose. With the valve fully open, hold the brush 2 cm off a board and watch the sheet part the bristles; then close it half and watch the water spread through them. Time a litre into the jug each way.
Шаг 10 - Image 1

Материалы для этого шага:

ВодаВода1 штука

Необходимые инструменты:

Мерный кувшинМерный кувшин
СекундомерСекундомер
ЛинейкаЛинейка
Садовый шлангСадовый шланг
11

A sheet that sprays, sputters or leaks

Sheet-of-water fountain brush troubleshooting.

Flow

Loading...
12

History and honest limits

**Frank L. Brinn**, a citizen of Canada residing in Milwaukee, filed US 840,604 on 20 February 1905; it was patented 8 January 1907. His cylinder is held to the block by a plate with packing and screws, its slots feeding the slot-apertures; the handle's end carries a rubber sheath and the valve; the cup, with its spout, collects the water instead of letting it run down the handle when the brush is raised. **Honest limits.** A slotted copper tube stands in for his cylinder, and a tin can for his cup. The notebook treats the sheet as uniform. What you see on the board is the result.

Материалы

11

Требуемые инструменты

18

CC0 Общественное достояние

Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.

Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.

Обсуждение

(0)

Войти чтобы присоединиться к обсуждению

Загрузка комментариев...