ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
AVENIR VERT
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Building a Djembe — The West African Rope-Tuned Goblet Drum
Woody

Créé par

Woody

3. juillet 2026NO
0
0
0
0
0

Building a Djembe — The West African Rope-Tuned Goblet Drum

Build a djembe: a goblet-shaped wooden drum with a goat-skin head, tuned not by heat but by PULLING ropes tight in a diamond weave. Carve the body, mount the skin on rings, then rope it up and tune it. A serious maker build in the membrane drum and rope tensioning, giving three voices — bass, tone and slap — from one head.
Intermédiaire
Several hours over several sessions

Consignes

1

A drum you tune with rope

The djembe is a goblet-shaped wooden drum with a goat-skin head. Instead of heating the skin to tune it, you pull ropes tight in a diamond weave — the tighter the rope, the higher and sharper the drum.
2

Carve the goblet body

Hollow a goblet-shaped body — a wide bowl at the top narrowing to a stem and opening out at the foot. Traditionally it is carved from a single log; built up from wood, keep the bore smooth and the bottom fully open.

Matériaux pour cette étape :

Dry Softwood BoardDry Softwood Board1 pièce
PVA Wood GluePVA Wood Glue1 pièce

Outils nécessaires :

Sloyd Carving KnifeSloyd Carving Knife
HacksawHacksaw
3

Cut the head

Cut a round goat-skin rawhide head a good bit wider than the drum's bowl, with the hair scraped off.

Matériaux pour cette étape :

RawhideRawhide1 pièce
4

Make two rings

Bend two metal rings that fit the drum's rim. Wrap one in the skin (the flesh ring) and leave one as a bottom ring; rows of rope loops hang from each.

Matériaux pour cette étape :

Bronze WireBronze Wire1 pièce
Abaca Tying TwineAbaca Tying Twine1 pièce
5

Mount the skin

Soak the skin, fold it over the top ring, and seat both over the bowl so the wet head lies across the mouth of the drum.
6

Rope it up

Lace a long rope up and down between the top ring's loops and the bottom ring, pulling the head down. Let it dry, then weave the verticals together in diamonds to pull them tighter still.

Matériaux pour cette étape :

Abaca Tying TwineAbaca Tying Twine1 pièce
7

Tune and play

Pull more diamonds to tighten the head and raise the pitch. Then play bare-handed: a deep BASS in the centre, a ringing TONE on the edge, and a sharp cracking SLAP with loose fingers on the rim.
8

Compendium — three voices and a tuning rope

The djembe is a goblet membrane drum, close kin to the darbuka, but two things set it apart. First, its body is a big carved WOODEN goblet, not clay: struck in the centre the head drives a slow pulse of air down the hollow stem and out of the open foot, which acts as a horn to boom the deep BASS; struck near the rim the edge of the skin snaps for a ringing TONE, and a loose, cracking hit gives the bright SLAP — three distinct voices from one head, the palette of West African drumming. Second, and cleverest, is how it is tuned. A drumhead's pitch rises with tension, and where the darbuka's skin is glued or warmed, the djembe's is pulled tight by ROPE: the head is trapped between two metal rings, and a long rope laced between them and then woven into diamonds draws the rings together and stretches the skin — pull more diamonds and the whole head tightens and the drum sings higher, all with no heat and no glue, tunable in a moment and re-tunable forever. This rope-lacing is the same idea that tunes the Korean janggu, and the djembe's goblet shape is the wooden cousin of the clay darbuka. Carved by the blacksmith-craftsmen of the Mande peoples for many centuries, the djembe is said to 'gather everyone in peace'.

Matériaux

5

Outils requis

2

You can swap these in

Can't get one of the materials? Swap it for an equivalent — these work just as well.

Blueprints liés

Ces blueprints partagent des connaissances — techniques, matériaux ou principes

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...