UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
Air-Pump Tube Dasher: A Tube Over a Loose Plunger Pumps Air at Every Stroke
Wright wanted a hand dasher that "will operate as an air pump to force a stream of air into the cream at the same time that it agitates it."
William M. Wright of Pittsburgh, Pennsylvania, received US 6,711, dated 11 September 1849, for an atmospheric churn-dasher: a tube of tinned sheet iron with a flange on its lower end, a cap with a valve opening inward, and a handle; inside, a loose cylinder of wood weighted at its lower end rests on the bottom of the tub as a plunger. Worked like a common dasher in "almost any ordinary pail or dairy vessel," it discharges air among the cream on each descent and refills on each ascent.
This rung works out the air per stroke, then prints the cap, flange and plunger, assembles them on a pipe, and makes butter in a pail.
Utangiye
About 1 hour, plus printing
Amabwiriza
1
1
Air per stroke
Air per stroke
Gupakira ikaye ya Jupyter…
2
2
A dash closing over a fixed block before it
A dash closing over a fixed block before it
The embedded blueprint squeezes air from a hollow dash over a block fixed to the churn. Wright's plunger is loose, so it needs no fixing at all.
3
3
Read US 6,711
Read US 6,711
"From the fact of the piston resting loosely upon the bottom of the tub, and being capable of moving about and occupying a vertical or inclined position as may best suit the convenience of the operator, and also from the facility with which it and the dasher may be removed from the churn tub and cleaned, and from the simplicity of all the parts being a guarantee against their getting out of order, this apparatus is applicable to churning cream in either large or small quantities."
4
4
Print the parts
Print the parts
Print the cap with its side valve port and handle socket, the foot flange, and the plunger, whose foot has a pocket for a steel weight. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Ibikoresho by'iyi ntambwe:
Fibere ya PETG1 igiceIbikoresho bikenewe:
Imashini icapa 3D ikoresha umugozi (FDM)5
5
Print the cap
Print the cap
The cap, printed as step 4 describes.
6
6
Print the flange
Print the flange
The flange, printed as step 4 describes.
7
7
Print the plunger
Print the plunger
The plunger, printed as step 4 describes.
8
8
Valve and weight
Valve and weight
Glue a small leather flap inside the cap over the valve port, along its top edge only, so air enters and cannot leave. Glue an M10 carriage bolt into the plunger's pocket, so it sinks in cream as he weighted his with metal.
Ibikoresho by'iyi ntambwe:
Umurongo w'uruhu1 igice
Bulo ifite umutwe uzengurutse1 igice
Epoksi y'Ibice Bibiri1 igiceIbikoresho bikenewe:
Ikusanyirizo ry'ibitorezi9
9
Assemble
Assemble
Cut 300 mm of 50 mm pipe. Push the flange onto its foot and the cap onto its top, and glue a hardwood dowel handle in the cap's socket. Stand the plunger in a tall food-grade bucket and lower the tube over it.
Ibikoresho by'iyi ntambwe:
Umuyoboro wa PVC1 igice
Udukoni tw'ibiti bikomeye1 igice
Indobo ya Litiro 201 igiceEpoksi y'Ibice Bibiri1 igiceIbikoresho bikenewe:
Umucumita w'Ibyuma
Urupapuro rwo Gusya10
10
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the pail, tube and flange cut away to show the loose weighted plunger standing on the bottom inside the tube, the cap with its valve, and the handle.
11
11
Dash and make butter
Dash and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Work the tube up and down over the plunger; bubbles should burst from under the flange on each down-stroke. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Ibikoresho by'iyi ntambwe:
Igice cy'ibinure cy'amata2000 ml
Umunyu w'inyanja munini1 igice
Amazi1 igiceIbikoresho bikenewe:
Igipima ubushyuhe gifite uruti rusigara mu kintu
Isaha yo Guhagarika
Iminzani ya Digitale yo mu Gikoni
Ibakure rinini ryo kuvanga ry'icyuma kitagira ingese12
12
No bubbles, a plunger that floats
No bubbles, a plunger that floats
Air-pump tube dasher troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**William M. Wright** of Pittsburgh, Allegheny County, Pennsylvania, received US 6,711, dated 11 September 1849. The plunger was to be "specifically heavier than cream," or wood weighted with a plug of metal; the tub could be any pail, "particularly, if it be deep in comparison with its width." He claimed the combination of the loose plunger with the tubular dasher.
**Honest limits.** A pipe and printed parts stand in for his tinned sheet-iron tube; use a food-grade pipe. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Ibikoresho
10- 1 igiceUmwanya
- 1 igiceUmwanya
- Umwanya
- 2 ibiceUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- 2000 mlUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
Ibikoresho bikenewe
8- Umwanya
- Umwanya
- Umwanya
- Umwanya
Dosiye z'igishushanyo
4Iki gishushanyo gikora
Blueprint zijyanye
Izi blueprint zisangira ubumenyi — uburyo, ibikoresho cyangwa amahame
Air-Pump Annular Dasher Churn: A Pump in the Middle, a Ring Dasher Round It
na Martin
IBIRIBWA N'IBINYOBWA
32
0
0
0
0
0
Trapped-Air Cylinder Dash Churn: A Hollow Dash That Squeezes Air Into the Cream
na Emma
IBIRIBWA N'IBINYOBWA
33
0
0
0
0
0
Valveless Cone Air Dasher: A Hollow Cone and Four Tubes, Nothing to Wear Out
na YourGrandma
IBIRIBWA N'IBINYOBWA
34
0
0
0
0
0
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.