Ubufatanye
UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
Angle Grinder: Reversible, with a Hollow Arbour and a Top Arbour Lock (Turley, US 5,718,621)
An angle grinder spins a disc at right angles to its motor: a bevel gear on the motor shaft turns a bevel gear on an upright arbour. E. M. Turley (US 5,718,621, 1998) makes the arbour hollow. A bolt runs down through it into a hexagonal coupling piece that drives the disc and clamps it against the arbour's flange, so the motor can run either way without loosening the disc.
To change the disc, a sliding lock piece on top locks the arbour, opens a hole over the bolt head and switches the motor off in one move.
Source: E. M. Turley, "Reversible Angle Grinder with Top Arbour Lock", US Patent 5,718,621 (filed 1996, granted 1998). Picture: its Fig. 1.
Hejuru
Unknown
Amabwiriza
1
1
Read Turley
Read Turley
"The angle grinder according to the preferred embodiment of the invention includes a reversible motor driving a hollow arbour via a right angle bevel gear arrangement. The arbour has a right angle flange at its bottom. The flange abuts against one side of the disk tool."
2
2
Turn the hollow arbour
Turn the hollow arbour
Turn an arbour hollow all through, with three outside shoulders (lower, middle and upper) for the two bearings and the bevel gear, and grooves above each for a snap ring. At the bottom, enlarge the bore into a hexagonal recess ending in a right-angle flange. At the top, enlarge the bore so the bolt head sits below the rim, and cut four equally spaced square notches (crenellations) in the rim. Sizes and metal are not given.
Ibikoresho by'iyi ntambwe:
Icyuma kitazwi1 arbourIbikoresho bikenewe:
Imashini yo guhinguza icyuma
Imashini ibaza icyuma
Amakariso (Ikariso ry'Intoki)
Ingano zitazwi3
3
Make the coupling piece and bolt
Make the coupling piece and bolt
Make a coupling piece: a hexagonal upper part that fits the arbour's recess, a round pilot that fits the standard centre hole of commercial grinding discs, and a right-angle flange at its base. Bore and tap it from the top, closed at the bottom. Make a retaining bolt long enough to run from the arbour's top down into the coupling piece, threaded at its lower end (Fig. 1 draws a socket in its head).
Ibikoresho by'iyi ntambwe:
Icyuma kitazwi1 coupling pieceIcyuma kitazwi1 retaining boltIbikoresho bikenewe:
Imashini yo guhinguza icyumaImashini ibaza icyuma
Agakoresho ko gukata imizingo y'ibyumaIngano zitazwi4
4
Cut the bevel gears
Cut the bevel gears
Cut two bevel gears with teeth at forty-five degrees (equal gears for a right-angle drive): one fixed on the arbour against its middle shoulder, one on the front end of the motor shaft. Tooth count and metal are not given.
Ibikoresho by'iyi ntambwe:
Icyuma kitazwi2 bevel gearsIbikoresho bikenewe:
Imashini ibaza icyuma
Icyuma gikata ingeri zihengamyeIngano zitazwi5
5
Assemble the drive
Assemble the drive
Mount a reversible electric motor in the housing, its shaft running back in a rear bearing and forward in a front bearing, the bevel gear on its front end. Set the arbour upright in two bearings at its lower and upper shoulders, the bevel gears meshing, with snap rings above the bearings and the gear. Drop the bolt down the arbour on a lock washer, fit the coupling piece from below and screw it on. Motor rating, housing material and how the bearings are held are not given.
Ibikoresho by'iyi ntambwe:
Moteri y'amashanyarazi1 reversible
Bearing y'utubumbe4 ibice
Ibikoresho bitazwi1 housingIbikoresho bikenewe:
Umutwe w'imfunguzo z'impande esheshatu
Uburyo bwo kubumba butazwiIngano zitazwi6
6
Fit the arbour lock
Fit the arbour lock
Make a rectangular lock piece that slides in the housing top across the arbour head, with a lever up through a slot in the housing, a tool hole, and a square tang underneath that drops into a rim notch. A spring on its front face holds it back in the running position. Fix a two-contact power switch to its rear so the motor circuit is broken when the piece is slid into the locking position. Cut a hole in the housing top over the bolt head and a slot for the lever.
Ibikoresho by'iyi ntambwe:
Icyuma kitazwi1 lock piece
Pirinye1 igice
Switch yo gucana no kuzimya1 igiceIbikoresho bikenewe:
Imashini ibaza icyuma
Icyuma Cyivumbura Gihagaze
Ibyuma Byinshi byo GucukuraAmakariso (Ikariso ry'Intoki)7
7
Change a disc
Change a disc
Push the lever forward: the tang locks the arbour, the switch cuts the motor and the tool hole sits over the bolt head. Unscrew the bolt from above with the key and pull the coupling piece; put the new disc on its pilot and screw it back up tight, so the disc is clamped between the arbour flange and the coupling flange. Let the lever spring back to run. Turley: a loose bolt cannot drop the disc, which rattles to warn you to tighten it.
Ibikoresho bikenewe:
Umutwe w'imfunguzo z'impande esheshatuIbikoresho
6- 1 lock pieceUmwanya
- 1 reversibleUmwanya
- Umwanya
- 1 housingUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
Ibikoresho bikenewe
10- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
Iki gishushanyo gikora
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.