Ubufatanye
UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
Aqueous PTFE Dispersion: Tetrafluoroethylene Polymerised in Soapy Water (Berry 1951)
Ordinary soaps stop tetrafluoroethylene from growing into long chains. A fluorine soap does not: with 2 % of ammonium dodecafluoroheptanoate in the water, the gas polymerises into tiny PTFE ribbons that stay suspended. The result is a milky dispersion, a third of it polymer, the raw material for PTFE fine powder.
Source: K. L. Berry (du Pont), US 2,559,752 (1951), Example III. Making the ammonium salt from our acid, and the apparatus, are ours. Picture drawn by Youblob.
Hejuru
1 day
Amabwiriza
1
1
Make the ammonium salt
Make the ammonium salt
Ours: neutralise about 1.9 parts of dodecafluoroheptanoic acid with ammonia solution until just neutral to litmus, giving 2 parts of ammonium dodecafluoroheptanoate. Make it up with distilled water to 93 parts of water in all. Parts are by weight.
Ibikoresho by'iyi ntambwe:
Aside dodekafluworoheputanoyike1.9 parts
Umuti wa amoniyake wa 25-28 %1 as required to neutralise
Amazi Yatunganyijwe93 partsIbikoresho bikenewe:
Urupapuro rwa litimusi
Ikibindi cy'ikirahure
Umunzani w'ibiro2
2
Load the pressure vessel
Load the pressure vessel
Put the solution in a pressure vessel with 0.05 part of potassium persulfate and 5 parts of paraffin wax melting at 56–58 °C. The wax protects the colloid while it is stirred.
Ibikoresho bikenewe:
Igitangiza cya persulfate
Ibuki rya parafine
Reyakitori y'igitutuUmunzani w'ibiro3
3
Heat and remove the air
Heat and remove the air
Bring it to 80–85 °C, then evacuate the vessel and hold it under reduced pressure for several minutes to drive out air and dissolved oxygen.
Ibikoresho bikenewe:
Reyakitori y'igitutu
Pompe ikuramo umwuka
Igipima Ubushyuhe4
4
Feed tetrafluoroethylene for 3.6 hours
Feed tetrafluoroethylene for 3.6 hours
Let in tetrafluoroethylene to 60 lb/sq in gauge. Agitate at 80–85 °C for 3.6 hours; each time the pressure falls to 55 lb/sq in, bring it back to 60.
Ibikoresho by'iyi ntambwe:
Tetrafluworoethileni1 as required to hold 55–60 psiIbikoresho bikenewe:
Reyakitori y'igitutu
Ibariro rya gazi ifite igitutu
Igipima UmuvudukoIgipima Ubushyuhe5
5
Cool and lift off the wax
Cool and lift off the wax
Cool it. The paraffin sets on top and lifts off. Below it is a colloidal PTFE dispersion with 34 % solids.
Ibikoresho bikenewe:
Reyakitori y'igitutu
Icupa ry'Ikirahure Rifite UmufunikoIbikoresho
4- 1.9 partsUmwanya
- 1 as required to neutraliseUmwanya
- 93 partsUmwanya
- 1 as required to hold 55–60 psiUmwanya
Ibikoresho bikenewe
11- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
- 1 vendor sell this, none ship to you yetUmwanya
- Umwanya
- Umwanya
Iki gishushanyo gikora
Blueprint zijyanye
Izi blueprint zisangira ubumenyi — uburyo, ibikoresho cyangwa amahame
Akaga
Dodecafluoroheptanoic Acid: the Fluoro Alcohol Oxidised with Permanganate (Berry 1951)
na Charlie
By'Inganda
8
0
0
0
0
0
Akaga
Tetrafluoroethylene: Chlorodifluoromethane Pyrolysed in a Silver Tube at 700 °C
na Charlie
By'Inganda
12
0
0
0
0
0
PTFE Resin Powder: Tetrafluoroethylene Polymerised under Pressure, Plunkett 1941
na Charlie
By'Inganda
12
0
0
0
0
0
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.