UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
Ibikoresho by'Ububaji
Ibishushanyo 47 birahari
Ibishushanyo (47)
Fit: A Joint That Needs a Mallet Is Too Tight
na Woody
Ububaji
47
0
0
0
0
0
Dovetails: Why They Point One Way, and What That Buys You
na Woody
Ububaji
37
0
0
0
0
0
The Mortise and Tenon: What Each Part of It Is Actually For
na Woody
Ububaji
50
0
0
0
0
0
Why a Butt Joint Fails: End Grain Does Not Glue
na Woody
Ububaji
47
0
0
0
0
0
Twist, Cup and Bow: Winding Sticks Make the Invisible Obvious
na Woody
Ububaji
54
0
0
0
0
0
The Marking Gauge: Distance From a Surface, Not a Number
na Woody
Ububaji
41
0
0
0
0
0
The Knife Line: A Mark You Can Put a Chisel Into
na Woody
Ububaji
43
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will
na Woody
Ububaji
49
0
0
0
0
0
Face Side and Face Edge: Everything Is Measured From the Same Two Surfaces
na Woody
Ububaji
43
0
0
0
0
0
Dividers: Laying Out Without Measuring Anything At All
na Woody
Ububaji
42
0
0
0
0
0
Cumulative Error: Why You Measure From One End, Not Piece to Piece
na Mark
Ububaji
41
0
0
0
0
0
Which Clamp: What Each Type Is For, and Making Your Own
na Woody
Ibikoresho by'Ububaji
43
0
0
0
0
0
The Dry Run: Assemble It Once With No Glue at All
na Woody
Ububaji
44
0
0
0
0
0
Clamping Pressure: Enough, Even, and Not Too Much
na Woody
Ububaji
53
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong
na Woody
Ibikoresho by'Ububaji
54
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule
na Forge
Ibikoresho by'Ubucuzi
56
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself
na Woody
Ibikoresho by'Ububaji
54
0
0
0
0
0
Starting a Cut: The First Three Strokes Decide the Rest
na Woody
Ibikoresho by'Ububaji
47
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order
na Woody
Ibikoresho by'Ububaji
32
0
0
0
0
0
Sawing Square: Two Lines at Once, and Fixing a Cut That Drifts
na Woody
Ibikoresho by'Ububaji
53
0
0
0
0
0
Sawing a Curve: Coping, Fret and Bow Saws
na Woody
Ibikoresho by'Ububaji
53
0
0
0
0
0
Rip and Crosscut: Two Saws Because Wood Has a Grain
na Woody
Ibikoresho by'Ububaji
46
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
na Forge
Ibikoresho by'Ubucuzi
60
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet
na Martin
Mekanike
47
0
0
0
0
0
Hagaragajwe 24 kuri 47