Ubufatanye
UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
Gear Motor: Small Motor on a Three-Shaft Box of Floating Gears (Swenson 1959)
A small motor with a reduction gearbox bolted on. Swenson's box has only three shafts: the motor shaft with its pinion, a fixed stub shaft, and the output shaft. The gears ride free on the two shafts in pairs and pass the drive back and forth between them, slower at each step. Only the last gear is fixed to the output shaft.
Source: Thure R. Swenson, US 2,908,180 (1959). Unknown: the motor, the fibre gear material, the thrust bearing, the metals, and every size and ratio. Swenson gives none of these, so they are linked to unknown heads. The machining is ours. Picture: the patent's drawing.
Impuguke
3 days
Amabwiriza
1
1
Make the housing and cover
Make the housing and cover
Make the gearbox: a housing with mounting bosses for the motor (Swenson's is a die-casting) and a front cover plate held by screws. Bore the housing for the motor-shaft nipple and for the output shaft's inner bearing, and form a seat in the cover for the outer sleeve bearing. Unknown: the metal and the sizes.
Ibikoresho by'iyi ntambwe:
Icyuma kitazwi1 as requiredIbikoresho bikenewe:
Imashini yo guhinguza icyuma
Icyegeranyo cy'ibikoresho by'imashini izunguruka (HSS)
Icyuma Cyivumbura Gihagaze
Agakoresho ko gukata imizingo y'ibyuma
Ingano zitazwi2
2
Cut the gears and shafts
Cut the gears and shafts
Make the stub shaft and the output shaft. Cut the train: a small pinion for the motor shaft; a fibre gear 34 with a pinion fixed to it; gear 23 with pinion; gear 35 with pinion; gear 24 with pinion; and the final gear 36. Unknown: the tooth numbers and ratios.
Ibikoresho by'iyi ntambwe:
Icyuma kitazwi1 as required
Igice cy’ibanze cy’ingiga ya fibre1 igiceIbikoresho bikenewe:
Imashini yo guhinguza icyuma
Imashini ikata amenyo ya gerere na hobIngano zitazwi3
3
Mount the motor with its front bearing on the housing
Mount the motor with its front bearing on the housing
The motor is conventional except for its front bearing: a casting held on the housing by screws, with a nipple fitting a bore in the housing and a sleeve bearing in the nipple. The motor shaft goes through it into the gearbox. Fix the small pinion on its end.
Ibikoresho by'iyi ntambwe:
Moteri ntoya ya induction1 igiceIbikoresho bikenewe:
Ikusanyirizo ry'ibitorezi
Ipiresi y'ukuboko4
4
Assemble the floating train
Assemble the floating train
On the output shaft, float the fibre gear (meshing with the motor pinion) and gear 35. On the stub shaft, float gears 23 and 24. Each drives the next by its pinion: 34 to 23, 23 to 35, 35 to 24, and 24 to the final gear 36. Press 36 onto the output shaft. Carry the output shaft in an inner bearing in the housing and a larger sleeve bearing in the cover, with a thrust ball bearing at its inner end. Screw the cover on.
Ibikoresho by'iyi ntambwe:
Bearingi y’imipira isunika1 igiceIbikoresho bikenewe:
Ipiresi y'ukubokoIkusanyirizo ry'ibitoreziIbikoresho
4- 1 as requiredUmwanya
- Umwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
Ibikoresho bikenewe
8- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
Iki gishushanyo gikora
Blueprint zijyanye
Izi blueprint zisangira ubumenyi — uburyo, ibikoresho cyangwa amahame
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.