ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
AVENIR VERT
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Cutting a Goose Quill Pen — Medieval Writing Instrument
Bob

Créé par

Bob

23. March 2026

Cutting a Goose Quill Pen — Medieval Writing Instrument

The quill pen was the primary writing instrument in Europe from the 6th to the 19th century. Goose feathers were preferred for general writing, while swan quills were prized for fine work and crow quills for detailed drawing. The feather must be cured (hardened by heat or ageing), and the nib cut to shape with a sharp pen-knife (the origin of that term). This blueprint covers preparing and cutting a goose quill.

Beginner
30-60 minutes

Instructions

1

Select and Cure the Feather

Select a large primary flight feather from a goose — the five outermost feathers from the left wing are preferred for right-handed writers, as their natural curve sweeps away from the writing hand. The barrel (calamus) should be at least 2 cm in diameter and free of cracks. Strip the barbs (the feathery vane) from the lower third of the shaft, leaving a clean barrel for gripping. To harden the barrel for a longer-lasting nib, cure it by soaking in water for several hours, then plunging the barrel into hot sand (approximately 150 degrees Celsius) for 10 to 20 seconds. The heat drives out residual moisture and tempers the keratin, making it harder, more transparent, and less prone to splitting. Alternatively, the quill can be air-cured by ageing for several months — medieval scriptoria kept stocks of feathers ageing on racks.

Step 1 - Image 1
2

Make the Initial Cut

Using a very sharp pen-knife, make a long diagonal cut across the end of the barrel at approximately 45 degrees, removing the tip and creating an angled opening. This cut should be approximately 2 to 3 cm long, exposing the hollow interior of the barrel. Clean out any membrane (the pith) from inside the barrel using the knife tip or a thin wire. The inside must be completely clean for ink to flow smoothly through the barrel by capillary action. Turn the quill over so the cut face is downward and make a short slit (approximately 5 to 8 mm long) in the centre of the cut, starting from the very tip. This slit is essential — it acts as an ink reservoir and allows the two tines of the nib to flex independently, controlling ink flow through capillary action as the pen is pressed against the writing surface.

3

Shape the Nib

Place the quill barrel on a hard cutting surface (a smooth stone or glass plate) with the slit facing up. Using the pen-knife, make two final cuts to shape the nib tip: first, cut the left shoulder at an angle from the barrel edge to the slit, then cut the right shoulder symmetrically. The resulting nib should have a broad, slightly curved tip approximately 1 to 2 mm wide for standard writing (narrower for fine work, wider for display lettering). Make a final straight cut across the very tip of the nib, perpendicular to the slit, to create a clean, sharp writing edge. This final cut must be made on a hard surface with a single decisive stroke — a ragged nib edge will produce scratchy, inconsistent lines. The nib shape determines the writing style: a broad nib cut at an angle produces the characteristic thick-and-thin strokes of medieval calligraphy.

Step 3 - Image 1
4

Test and Adjust the Nib

Dip the nib approximately 5 mm into ink and test it on parchment or good-quality paper. The ink should flow smoothly from the nib as you write, producing a consistent line that varies in width as you change the angle and pressure. If the ink does not flow, the slit may be too short — extend it by 1 to 2 mm. If the ink blobs or flows too freely, the slit may be too long or too wide — re-cut the nib tip to narrow it. If the pen scratches, the nib tip is not smooth — polish it on a fine whetstone or fine sandpaper. A properly cut quill should produce approximately 10 to 15 lines of text before needing to be re-dipped. Medieval scribes re-cut their nibs frequently — a quill might be re-trimmed dozens of times before the barrel became too short to hold comfortably, at which point a new feather was used.

5

Maintain the Quill

Between writing sessions, rinse the nib in clean water and blot dry to prevent ink from drying in the slit and clogging the capillary channel. Store the quill horizontally or nib-up to prevent ink from settling back into the barrel. A well-cured quill nib will hold its edge for several hours of continuous writing before needing re-cutting — place the nib on the cutting surface and shave a thin slice from the tip to restore the sharp edge. Medieval scribes kept their pen-knives always at hand for this purpose. A single goose feather typically provides enough barrel length for the nib to be re-cut 15 to 20 times before the barrel is exhausted. Goose feathers were available in quantity from domestic flocks, and large scriptoria consumed thousands of feathers annually — the monastery of St. Gallen in Switzerland records purchasing feathers by the cartload.

Matériaux

  • Large goose flight feathers (from the left wing for right-handed writers) - 3-5 feathers pieceEspace réservé
    Voir
  • Fine sand (heated, for curing the quill barrel) - small amount pieceEspace réservé
    Voir

Outils requis

  • Sharp pen-knife or craft knife
  • Small pan of heated sand (for curing)

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Discussion

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...