Ubufatanye
UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
English
Rubber Squeeze Bulb: Latex Coagulated Inside a Split Mould Coated with Calcium Nitrate (Szegvari, Anode, US 1,949,502)
A seamless hollow rubber bulb grows inside a closed mould: the cavity is coated with a coagulant, the mould is filled with latex, and rubber sets on the walls until it is thick enough. The rest of the latex is poured out through the neck.
Result: a seamless rubber squeeze bulb with a neck; ours sized at about 60 ml.
Source: Szegvari, US 1,949,502 (American Anode, 1934); his example is a football bladder. Not given: times, strengths, vulcanising details. Picture drawn by Youblob.
Hagati
2 days
Amabwiriza
1
1
Coat the mould cavity with calcium nitrate in acetone
Coat the mould cavity with calcium nitrate in acetone
Open the split mould and coat only the cavity with a solution of calcium nitrate in acetone, by brush or spray. The acetone evaporates and leaves a sticky film of coagulant. Ours: a cavity of about 60 ml with a neck.
Ibikoresho bikenewe:
Nitrate ya kalisiyumu
Asetone
Ifumbire y’umupira y’ibice bibiri
Uburoso bugari2
2
Close the mould under the latex
Close the mould under the latex
Lower both halves under the surface of latex and close them once they are submerged and the air bubbles are gone. Rubber now sets on the coated walls; the longer the contact, the thicker the wall.
Ibikoresho by'iyi ntambwe:
Umupira w'igiti karemano1 as requiredIbikoresho bikenewe:
Inkono Nini3
3
Pour out the extra latex through the neck
Pour out the extra latex through the neck
Lift the mould out and turn it over so the liquid latex drains back through the neck. Refill with water holding a little acetic acid so the inner face sets too.
Ibikoresho bikenewe:
Asidi asetike (isukuye cyane)
Amazi4
4
Open under warm water and leach
Open under warm water and leach
Open the mould under running warm water, take out the bulb and leave it in the water until most of the soluble matter has leached out. Clean any liquid latex off with dilute ammonia.
Ibikoresho bikenewe:
Amazi
Umuti wa amoniyake wagabanyijwe5
5
Inflate lightly and dry
Inflate lightly and dry
Drain the bulb, inflate it lightly so it does not collapse, and dry it at room temperature or in a drying cabinet. The latex may hold sulphur and be vulcanised in the usual way; Szegvari gives no details.
Ibikoresho bikenewe:
Ifuru yo kumishahoIbikoresho
1- 1 as requiredUmwanya
Ibikoresho bikenewe
9- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
Iki gishushanyo gikora
Blueprint zijyanye
Izi blueprint zisangira ubumenyi — uburyo, ibikoresho cyangwa amahame
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.