UBUHANZI
UBWIZA N'UBUZIMA
UBUKORIKORI
UMUCO N'AMATEKA
IMYIDAGADURO
IBIDUKIKIJE
IBIRIBWA N'IBINYOBWA
UBWUBATSI BUSUBIRA INYUMA
UBUMENYI
SIPORO
IKORANABUHANGA
IBYAMBARWA
Twisted-Strip Egg Beater: Faces Beat and Edges Cut
A wire beater passes through the egg and leaves a wake without much froth.
James P. McLean and Philemon A. Morley of Brooklyn received US 28,760, dated 19 June 1860, for an egg beater of corrugated or twisted strips of tin turned inside a can by a large and a small cog gear set between the double heads of its lid: "by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof."
This rung works out how much of a twisted face pushes, then prints the gears and a cage of twisted strips, builds the lid drive on a can, and times a beating.
Hagati
About 4 hours, plus printing
Amabwiriza
1
1
How a twisted face beats
How a twisted face beats
Gupakira ikaye ya Jupyter…
2
2
A geared wire beater before it
A geared wire beater before it
The embedded blueprint beats with bent wires. McLean and Morley use twisted strips with faces and edges.
3
3
Read US 28,760
Read US 28,760
"The superiority of our arrangement of egg beaters over those that are in common use, is that by means of twisted or corrugated strips of metal the gelatin mass is beaten by the flat surfaces as well as being broken or cut by the sharp edges thereof, hence the action is analogous to the motion produced by the hand and spoon, whereas an ordinary wire beater simply passes through the egg like the rudder of a boat, leaving a simple wake behind it without producing an immediate fomentation as is the case with our beater."
4
4
Print the gears and cage
Print the gears and cage
Print the 36-tooth gear, the 12-tooth gear and the cage of four twisted strips. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Ibikoresho by'iyi ntambwe:
Fibere ya PETG1 igiceIbikoresho bikenewe:
Imashini icapa 3D ikoresha umugozi (FDM)5
5
Print the 36-tooth gear
Print the 36-tooth gear
The 36-tooth gear, printed as step 4 describes.
6
6
Print the 12-tooth gear
Print the 12-tooth gear
The 12-tooth gear, printed as step 4 describes.
7
7
Print the cage
Print the cage
The cage, printed as step 4 describes.
8
8
Make the double lid
Make the double lid
Cut two plywood disks to the can's mouth. Space them 20 mm apart on three M5 screws with nuts, and drill both for the crank shaft and the cage shaft 48 mm apart.
Ibikoresho by'iyi ntambwe:
Urupapuro rw'ibiti byometse1 igice
Ibitorezo by'imashini1 igice
Umupira w'Impande Esheshatu1 igice
Uruziga Rurambuye1 igiceIbikoresho bikenewe:
Umucumita w'Imigororwa
Icyuma Cyivumbura Kidafite Insinga
Ibyuma Byinshi byo Gucukura
Isupana ihindurwa
Ikigereranyo cya Digitale cy'Amasentimetero 69
9
Fit the shafts and gears
Fit the shafts and gears
Epoxy the large gear on a crank shaft of 5 mm rod with a bent handle, and the small gear on the cage shaft, both between the heads. Epoxy the cage on the cage shaft's lower end.
Ibikoresho by'iyi ntambwe:
Umurongo Uzengurutse w'Icyuma Cyoroshye1 igice
Epoksi y'Ibice Bibiri1 igiceIbikoresho bikenewe:
Umucumita w'Ibyuma
Ifatiro ry'Ameza
Ipfundo Rifite Umunwa Uringaniye10
10
The patent drawing
The patent drawing
US 28,760 drawing sheet, public domain (expired patent).
11
11
Beat egg whites
Beat egg whites
Put two egg whites in the can, fit the lid, and crank about once a second; time to stiff peaks.
Ibikoresho by'iyi ntambwe:
Ikopo ry'icyuma1 igice
Igi2 ibiceIbikoresho bikenewe:
Isaha yo Guhagarika12
12
Gears that skip, a cage that scrapes
Gears that skip, a cage that scrapes
Twisted-strip egg beater troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**James P. McLean** and **Philemon A. Morley** of Brooklyn, assignors to P. A. Morley, received US 28,760, dated 19 June 1860. Their Fig. 2, for bakers, puts the strips on a vertical water-tight cylinder turning round a stationary handle, driven by a hand wheel whose rubber band grips the cylinder's grater-like funnel top instead of cog wheels. They claimed the twisted beaters in combination with the cylinder.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed strips and plywood heads stand in for tin. Your times are the result.
Ibikoresho
9- 1 igiceUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- Umwanya
- 1 igiceUmwanya
- 1 igiceUmwanya
- 2 ibiceUmwanya
Ibikoresho bikenewe
10- Umwanya
- 1 vendor sell this, none ship to you yetUmwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
- Umwanya
Dosiye z'igishushanyo
3Iki gishushanyo gikora
Blueprint zijyanye
Izi blueprint zisangira ubumenyi — uburyo, ibikoresho cyangwa amahame
CC0 Umurenge rusange
Iyi blueprint yasohowe munsi ya CC0. Ushobora gukoporora, guhindura, gukwirakwiza no gukoresha nta kwemererwa.
Shyigikira Umuremyi ugura ibicuruzwa binyuze muri Blueprint ye Komisiyo y'Umuremyi byashyizweho n'Abacuruzi, cyangwa kora verisiyo nshya y'iyi Blueprint ukayinjiza nk'isano muri Blueprint yawe kugira ngo musangire inyungu.