فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
المستقبل الأخضر
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Making a Clay Crucible for Smelting — The Vessel That Holds Molten Metal
The clay crucible is the most essential tool in early metallurgy — a hand-formed vessel of refractory clay and grog that can withstand the 1,100 °C temperatures needed to melt copper and bronze. Without it, smelting is impossible.
This blueprint follows the Bronze Age method of mixing local clay with crushed pottery (grog) to create a thermal-shock-resistant vessel. The grog opens the clay body, allowing steam to escape during firing instead of shattering the crucible. The thick walls and tapered form channel heat inward while the pouring lip allows controlled transfer of molten metal into moulds.
Every bronze tool, weapon, and ornament of the ancient world began inside a vessel like this one.
متوسط
6-8 hours (plus drying and firing)
التعليمات
1
1
Collect and prepare the clay
Collect and prepare the clay
Dig refractory clay from a deposit near a riverbank or hillside. Remove stones, roots, and organic debris by hand. Break the clay into walnut-sized lumps and spread on a flat stone to dry in the sun for one day.
المواد لهذه الخطوة:
Refractory Clay2 كغ2
2
Crush fired pottery into grog
Crush fired pottery into grog
Take broken pieces of previously fired pottery or old crucible fragments. Place them on a flat stone and crush with a hammerstone until reduced to coarse grains no larger than 3 mm. Sieve out any fine dust — you want sharp angular grains that interlock with the clay body.
المواد لهذه الخطوة:
Grog (Crushed Fired Pottery)500 غ3
3
Mix the crucible body
Mix the crucible body
Combine 2 parts dry clay with 1 part grog and a handful of clean quartz sand on a flat working stone. Mix thoroughly while dry, then add water gradually. Knead the mixture like bread dough for at least 10 minutes until it becomes a uniform, stiff paste with no dry pockets.
المواد لهذه الخطوة:
Quartz Sand (clean)200 غ
Water500 ملالأدوات المطلوبة:
Flat Stone Slab
Wooden Mixing Stick4
4
Wedge the clay to remove air
Wedge the clay to remove air
Slam the clay mass onto the stone and fold it over itself repeatedly. Push down with the heel of your hand, fold, rotate 90 degrees, repeat. Do this at least 30 times. Air bubbles trapped in the wall will expand when heated and explode the crucible.
5
5
Form the base
Form the base
Tear off a ball of clay the size of your fist. Press it flat on the working stone into a disc about 8 cm across and 2 cm thick. This is the crucible floor — it must be uniformly thick with no thin spots.
6
6
Build up the walls with coils
Build up the walls with coils
Roll clay into ropes about 1.5 cm thick. Lay the first coil around the edge of the base disc, pressing it firmly to bond. Score the joining surfaces with a stick before adding each coil. Stack coils one upon another, angling slightly outward to create a tapered cup shape. Build to about 12 cm tall.
7
7
Smooth and compress the walls
Smooth and compress the walls
Use a smooth stone on the outside and your fingers inside to press the coils together into a solid wall. Work upward from the base, compressing until no coil seams are visible. The finished wall should be 1.5-2 cm thick — thinner will crack, thicker wastes fuel.
الأدوات المطلوبة:
Smooth Stone8
8
Form the pouring lip
Form the pouring lip
At one point on the rim, pinch the clay outward and downward to create a V-shaped spout about 3 cm long. This channels molten metal in a controlled stream when you tilt the crucible. Make the lip thick — it bears the most stress during pouring.
9
9
Thicken the base and lower walls
Thicken the base and lower walls
Add an extra coil of clay around the bottom third of the outside and smooth it in. The base takes the most heat and holds the heaviest pool of liquid metal. A reinforced base prevents blowout.
10
10
Dry the crucible slowly
Dry the crucible slowly
Set the crucible in shade for 2-3 days, turning it daily. Do not place it in direct sun — fast drying causes surface cracks. The clay must lose moisture evenly through the entire wall thickness. The crucible is ready when it feels warm-cool to the touch, not cold.
11
11
Pre-heat near a fire
Pre-heat near a fire
Place the bone-dry crucible near (not in) a small fire for 2 hours, rotating occasionally. This drives out any remaining moisture trapped deep in the clay. Steam escaping too fast from a cold crucible placed directly into a kiln will shatter it.
12
12
Fire the crucible in a kiln
Fire the crucible in a kiln
Place the pre-heated crucible into a charcoal-fueled kiln or pit firing. Raise temperature slowly over 3-4 hours to at least 900 °C. The grog particles prevent the clay from shrinking unevenly. Hold at peak temperature for 1 hour, then allow to cool overnight without opening the kiln.
13
13
Inspect and test
Inspect and test
When cool, tap the crucible with a knuckle — a clear ring means fully vitrified, a dull thud means under-fired. Check for cracks, especially around the base and pouring lip. A properly made crucible will survive 5-10 melts before the thermal cycling degrades it.
المواد
4- 2 كغعنصر نائب
- عنصر نائب
- 200 غعنصر نائب
الأدوات المطلوبة
3- عنصر نائب
- عنصر نائب
- عنصر نائب
مواد المخططات المرتبطة
المخططات ذات الصلة
هذه المخططات تشارك المعرفة مع هذا — التقنيات والمواد والمبادئ
Related blueprints
Other builds that share materials, tools, or techniques with this one.
Forging an Iron Chisel — The Cutting Tool That Shapes Stone, Wood, and MetalMetalworking
Making a Bronze Torc — Twisting and Bending a Neck RingMetalworking
Making a Bronze Awl — The Leatherworker's Piercing ToolMetalworking
Forging an Iron Axe Head — The Tool That Cleared the ForestsMetalworking
Forging an Iron Strap Hinge — The Joint That Opens Every DoorMetalworking
Casting a Bronze Flat Axe — The First Metal Cutting ToolMetalworking
CC0 ملكية عامة
هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.
ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.