التعاون
فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Carbon Resistance Strip: Carbon and Phenolic Resin in Acetone, Cured on Semi-Cured Phenolic Sheet
Ed

أنشأه

Ed

21. أكتوبر 2026FI
21
0
0
0
0

Carbon Resistance Strip: Carbon and Phenolic Resin in Acetone, Cured on Semi-Cured Phenolic Sheet

Podolsky (Wirt Company, US 2,060,114, 1936) bonded the carbon film into its base: the phenolic sheet is only half cured, the coating carries the same kind of resin, and its solvent (acetone) softens the sheet's surface. Heated calender rolls then finish the cure of sheet and coating together, so the track is hard, does not rub off and lasts. Cut across, the sheet gives resistance strips for a variable resistor. The picture: our diagram.
متوسط
1 day

التعليمات

1

Mix 21 carbon, 26 resin, 53 solvent

Make a solution of 21 % carbon, 26 % phenol-formaldehyde resin and 53 % acetone. The patent says the exact proportions are not essential; this is its example.

المواد لهذه الخطوة:

كربونكربون21 parts
باكليت سائل (ناتج تكاثف الفينول والفورمالديهيد)باكليت سائل (ناتج تكاثف الفينول والفورمالديهيد)26 parts

الأدوات المطلوبة:

أسيتونأسيتون
ميزان ذو كفّتينميزان ذو كفّتين
كأس زجاجي مدرّجكأس زجاجي مدرّج
محرّك تقليبمحرّك تقليب
قناع تنفّس كامل الوجهقناع تنفّس كامل الوجه
قفازات مطاطيةقفازات مطاطية
2

Coat the semi-cured sheet

Use a phenolic sheet whose cure was stopped before it fully hardened. A roller turning in a pan of the solution coats its underside.

المواد لهذه الخطوة:

لوح فينولي نصف معالجلوح فينولي نصف معالج1 قطعة

الأدوات المطلوبة:

زوج أسطوانات الطلاء بالغمسزوج أسطوانات الطلاء بالغمس
قناع تنفّس كامل الوجهقناع تنفّس كامل الوجه
قفازات مطاطيةقفازات مطاطية
3

Cure between calender rolls at 350 °F

Pass the coated sheet between calender rolls heated to about 350 °F (177 °C). This finishes the cure and bonds the coating to the sheet. The patent sometimes calenders it again to burnish the surface.

الأدوات المطلوبة:

أسطوانات كالندر مسخّنةأسطوانات كالندر مسخّنة
قفّازات مقاومة للحرارةقفّازات مقاومة للحرارة
4

Cut into strips

Cut the sheet across into strips of the width wanted. Ours: tin snips.

الأدوات المطلوبة:

مقصّ صفائحمقصّ صفائح
قفازات مطاطيةقفازات مطاطية

المواد

3

الأدوات المطلوبة

10

CC0 ملكية عامة

هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.

ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.

النقاش

(0)

تسجيل الدخول للمشاركة في النقاش

جارٍ تحميل التعليقات...