فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights
Penny

أنشأه

Penny

14. أكتوبر 2026DK
15
0
0
0
0

Equal-Arm Balance on a Knife Edge, with a Set of Brass Weights

The oldest weighing machine is a beam with equal arms balanced on a pivot, a pan hanging from each end: put the load in one pan and known weights in the other until the beam lies level. Balances go back to the Fourth Dynasty of Egypt. A hardened knife edge makes it sensitive and a long pointer shows the smallest tilt; the weights are cast in brass and adjusted against each other. The picture: our diagram of the balance, its knife edge, pointer, pans and weights.
متوسط
Two to three days

التعليمات

1

Beam and knife edge

File a straight beam from flat tool steel with a hole exactly in the middle and one near each end, the two end holes equally far from the centre. Forge and file a short steel knife edge, harden and temper it, and fit it through the centre hole, edge down. File a long pointer onto the beam.

المواد لهذه الخطوة:

قضيب مسطّح من فولاذ العددقضيب مسطّح من فولاذ العدد1 قطعة

الأدوات المطلوبة:

مبرد معادنمبرد معادن
مثقب يدويمثقب يدوي
قدمة رقمية 6 بوصاتقدمة رقمية 6 بوصات
كور الحدّادكور الحدّاد
حوض تبريد الحدادةحوض تبريد الحدادة
نظارات أماننظارات أمان
2

Stand and bearing

Make an upright stand of hardwood with a hardened steel V-block on top, shallower than the knife edge, so the beam rocks freely. Mark a zero line behind the pointer.

المواد لهذه الخطوة:

شريط خشب صلبشريط خشب صلب2 قطع
قضيب فولاذ طريقضيب فولاذ طري0.3 m

الأدوات المطلوبة:

مبرد معادنمبرد معادن
كور الحدّادكور الحدّاد
حوض تبريد الحدادةحوض تبريد الحدادة
3

Pans

Cut two equal brass discs, dish them slightly, drill three holes in each rim and hang each from an end hole on three equal cords.

المواد لهذه الخطوة:

صفيحة نحاس أصفرصفيحة نحاس أصفر1 قطعة
خيط كتّان مشمّعخيط كتّان مشمّع3 m

الأدوات المطلوبة:

مقصّ صفائحمقصّ صفائح
مثقب يدويمثقب يدوي
مبرد معادنمبرد معادن
4

Trim to level

With both pans empty, file the heavier side until the pointer rests on zero. Swap the pans and check again: if the pointer moves, the arms are unequal and the end holes need moving.

الأدوات المطلوبة:

مبرد معادنمبرد معادن
5

Cast the weights

Melt brass and cast a row of plain cylinders a little heavy in green sand.

المواد لهذه الخطوة:

سبيكة نحاس أصفرسبيكة نحاس أصفر2 كغ
فحم نباتيفحم نباتي1 as required
رمل السباكةرمل السباكة5 كغ

الأدوات المطلوبة:

كور الحدّادكور الحدّاد
بوتقة من طين حراريبوتقة من طين حراري
ملقط بوتقةملقط بوتقة
صندوق سبك (علوي وسفلي)صندوق سبك (علوي وسفلي)
قفازات لحامقفازات لحام
6

Adjust the weights

Balance the largest weight against a litre of water measured in the cylinder (one kilogram, our reference), filing it down until the beam is level. Make the smaller ones by balancing pairs against a larger one and against each other, filing each to level.

المواد لهذه الخطوة:

ماءماء1 لتر

الأدوات المطلوبة:

مخبار مدرّجمخبار مدرّج
مبرد معادنمبرد معادن
7

A binary set of weights

جارٍ تحميل دفتر Jupyter…
8

Limits

The balance's form and use are as Wikipedia describes; the sizes and the water reference are ours. Water's density changes a little with temperature, so the reference is good to a few parts in a thousand.

المواد

9

الأدوات المطلوبة

12

المخططات ذات الصلة

هذه المخططات تشارك المعرفة مع هذا — التقنيات والمواد والمبادئ

CC0 ملكية عامة

هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.

ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.

النقاش

(0)

تسجيل الدخول للمشاركة في النقاش

جارٍ تحميل التعليقات...