فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
المستقبل الأخضر
الهندسة العكسية
SCHOOL PROJECTS
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Making a Coiled-Straw Bee Skep — The Traditional Beehive Before Wooden Boxes
The bee skep is the coiled-straw beehive that housed honeybees across Europe for roughly two thousand years, from antiquity into the 1800s, before wooden box hives replaced it. Using the same coiling technique as a straw basket, long rye straw is wound into a dome and stitched together with split cane. This blueprint builds a traditional skep by hand — from preparing the straw to the finished, weatherproofed hive ready to house a swarm.
متوسط
8
التعليمات
1
1
Harvest and clean long rye straw
Harvest and clean long rye straw
Cut long rye or wheat straw and strip off the seed heads and leaf sheaths, keeping the hollow stems long and unbroken for strong coils.
المواد لهذه الخطوة:
Rye Straw1 حزمةالأدوات المطلوبة:
Knife2
2
Split and soak the binding cane
Split and soak the binding cane
Split lengths of cane into thin flexible strips and soak them in water until pliable — these will sew the straw coils together.
المواد لهذه الخطوة:
Split Cane1 حزمة
Water3 لتراتالأدوات المطلوبة:
Knife3
3
Make the girth gauge
Make the girth gauge
Form a small open ring about 2.5 cm across (the traditional 'girth', often a cow-horn tip). Straw fed through it keeps every coil the same thickness.
الأدوات المطلوبة:
Skep Girth Gauge4
4
Bind the crown
Bind the crown
Take a small handful of straw, bend it into a tight knot to form the top knob of the skep, and lash it firmly with a strip of split cane.
المواد لهذه الخطوة:
Rye Straw1 حزمةSplit Cane1 مترالأدوات المطلوبة:
Awl5
5
Feed straw into an even rope
Feed straw into an even rope
Pass straw through the girth to form a continuous rope of even thickness, adding a few stems at a time so the bundle never thins as you work.
المواد لهذه الخطوة:
Rye Straw1 حزمةالأدوات المطلوبة:
Skep Girth Gauge6
6
Sew the first coils to the crown
Sew the first coils to the crown
Coil the straw rope in a tight spiral around the crown. Push the awl through the coil below, pass split cane through, and pull each stitch snug about every 2 cm.
المواد لهذه الخطوة:
Split Cane1 مترالأدوات المطلوبة:
Awl7
7
Spiral outward to start the dome
Spiral outward to start the dome
Continue spiralling outward from the crown, binding each new coil to the one below. The domed top of the hive begins to take shape.
المواد لهذه الخطوة:
Rye Straw1 حزمةSplit Cane1 مترالأدوات المطلوبة:
Awl8
8
Build the domed wall downward
Build the domed wall downward
Work the spiral down and out to build the wall, keeping the girth on the rope to hold thickness and every binding stitch tight and evenly spaced.
المواد لهذه الخطوة:
Rye Straw1 حزمةSplit Cane1 مترالأدوات المطلوبة:
AwlSkep Girth Gauge9
9
Keep the courses even
Keep the courses even
Control how far each coil steps outward so the dome stays smooth and symmetrical. Steady, even courses make a strong, weathertight hive.
المواد لهذه الخطوة:
Rye Straw1 حزمةالأدوات المطلوبة:
Awl10
10
Widen to the finished base
Widen to the finished base
As you near the bottom, let the coils reach the finished diameter of about 35–40 cm — the standard size for a colony of bees.
المواد لهذه الخطوة:
Rye Straw1 حزمةSplit Cane1 مترالأدوات المطلوبة:
Awl11
11
Cut the flight entrance
Cut the flight entrance
At the lower edge, cut a small entrance notch in a coil so the bees can come and go once the skep is set open-side down.
الأدوات المطلوبة:
Knife12
12
Finish and lock the base coil
Finish and lock the base coil
Complete the last coil at the base, taper off the straw rope, and lock the final binding stitches so the skep cannot unravel.
المواد لهذه الخطوة:
Split Cane1 مترالأدوات المطلوبة:
Awl13
13
Trim the skep clean
Trim the skep clean
Trim protruding straw ends and stray cane with the knife to leave a clean rim and an even outer surface.
الأدوات المطلوبة:
Knife14
14
Clom the outside for weatherproofing
Clom the outside for weatherproofing
Smear a thin coat of cow-dung-and-clay daub over the straw to shed rain and seal drafts, then let it dry — the traditional 'clomming'.
المواد لهذه الخطوة:
Cow Dung2 كغ
Ball Clay1 كغ15
15
Cure the finished skep
Cure the finished skep
Cure the skep in a dry, airy place. Once fully dry it is ready to hive a swarm — set open-side down on a board or stand.
المواد
6- 1 حزمةعنصر نائب
- 6 أمتارعنصر نائب
مواد المخططات المرتبطة
You can swap these in
Can't get one of the materials? Swap it for an equivalent — these work just as well.
- Instead of Ball Clay, try:
Refractory Clay
Wild Clay
Porcelain Clay
Kaolin Clay Powder - Instead of Water, try:
Distilled Water (1 Liter) - Instead of Knife, try:
Blunt Collection Knife
Gilder's Knife - Instead of Skep Girth Gauge, try:
Marking Gauge
Stainless Steel 316 Sheet 16 Gauge
Sterling Silver Wire 925 20 Gauge
Wire Tension Monitoring Gauge - Instead of Rye Straw, try:
Stainless Steel Straw Set (8-Pack)
المخططات ذات الصلة
هذه المخططات تشارك المعرفة مع هذا — التقنيات والمواد والمبادئ
Related blueprints
Other builds that share materials, tools, or techniques with this one.
Making a Sistrum — The Sacred Rattle of Ancient Egypt
Saving Lettuce Seeds — Letting the Leaf Crop Bolt
Making a Leather Sling — The Shepherd's Projectile Weaponsurvival
Making a Clay Crucible for Smelting — The Vessel That Holds Molten MetalMetalworking
Making a Bronze Awl — The Leatherworker's Piercing ToolMetalworking
Making a Fire-Hardened Hunting Spear — The Oldest Weaponsurvival
CC0 ملكية عامة
هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.
ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.