فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
المستقبل الأخضر
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Tentering Cloth on a Frame — Stretching Fulled Wool to Set Width and Grain
Tentering is the critical finishing step between fulling and napping that transforms shapeless, shrunken fulled wool into cloth of uniform width and straight grain. The wet fulled fabric is hooked onto rows of L-shaped iron hooks — tenterhooks — driven into the rails of a large outdoor wooden frame, then stretched to its proper dimensions and left to dry in the open air. Without tentering, fulled cloth dries unevenly, shrinks to unpredictable widths, and develops a skewed grain that makes cutting and tailoring impossible. The process was so central to the medieval wool trade that every cloth town maintained communal tentergrounds, and the phrase "on tenterhooks" — meaning in a state of anxious suspense — entered the English language from this very practice. This blueprint covers the complete tentering process using a traditional two-rail tenter frame.
مبتدئ
4-8 hours (mostly drying time)
التعليمات
1
1
Inspect the fulled cloth
Inspect the fulled cloth
Examine the fulled cloth fresh from the fulling process. It should be thoroughly matted — individual yarns no longer visible on the surface — and significantly thicker and narrower than the original woven piece. The cloth will feel dense and slightly spongy when wet.
المواد لهذه الخطوة:
Fulled Wool Cloth1 قطعة2
2
Rinse the cloth clean
Rinse the cloth clean
If the cloth still carries fuller's earth or residual soap from fulling, rinse it thoroughly in clean cold water until the runoff is clear. Squeeze gently — never wring or twist, which distorts the grain. The cloth must be damp but not dripping for tentering.
المواد لهذه الخطوة:
Clean Water20 لتراتالأدوات المطلوبة:
Washing Basin3
3
Measure the target width
Measure the target width
Check the intended finished width of the cloth — this was regulated by guild ordinances in medieval towns, typically between 1.5 and 2 yards (137-183 cm). Measure the current width of the damp fulled cloth. It will be narrower than the target, having shrunk 20-40% during fulling.
الأدوات المطلوبة:
Measuring Tape 3m4
4
Position the tenter frame
Position the tenter frame
The tenter frame stands outdoors in an open field with good air circulation and sun exposure. A traditional frame consists of two long horizontal oak rails — upper and lower — supported on stout upright posts set into the ground. The rails should be slightly longer than the cloth and spaced apart at the target cloth width.
الأدوات المطلوبة:
Tenter Frame5
5
Check the tenterhooks
Check the tenterhooks
Inspect the tenterhooks — small L-shaped iron hooks hammered into the top face of both rails at regular intervals of 5-8 cm. Each hook curves upward with a sharp point that grips the cloth. Ensure no hooks are bent, missing, or blunted. Replace any damaged hooks before mounting the cloth.
الأدوات المطلوبة:
Tenterhooks6
6
Hook the upper selvedge
Hook the upper selvedge
Begin at one end of the upper rail. Press the selvedge (woven edge) of the cloth firmly onto the first tenterhook so the point pierces through the selvedge and the hook grips the edge. Work along the rail, hooking the selvedge onto every hook. Keep the cloth hanging straight down under its own weight.
7
7
Stretch and hook the lower selvedge
Stretch and hook the lower selvedge
Return to the starting end. Pull the lower selvedge of the hanging cloth downward to the lower rail and hook it onto the first tenterhook. Work along the lower rail, pulling the cloth taut and hooking at each point. Apply firm, even tension — the cloth should be stretched to its target width without tearing the selvedge.
8
8
Even the tension across the cloth
Even the tension across the cloth
Step back and sight along the frame. The cloth should be uniformly taut with no sagging pockets or over-stretched thin patches. Rehook any uneven sections. The warp threads (running lengthwise) should hang straight and parallel, the weft (crosswise) running perpendicular. This sets the grain.
9
9
Smooth the surface by hand
Smooth the surface by hand
Run your hands across the surface of the stretched cloth. Press out any wrinkles, folds, or bubbles trapped in the wet fabric. Work from the centre outward toward the selvedges. A smooth surface at this stage means a smooth finished cloth.
10
10
Stretch the length if needed
Stretch the length if needed
If the cloth has also shrunk excessively in length during fulling, pull it gently lengthwise along the rail. Some tenter frames had adjustable end-bars for lengthwise stretching. Be conservative — over-stretching weakens the cloth and can distort the weave permanently.
11
11
Leave to dry in the air
Leave to dry in the air
Allow the cloth to dry completely on the frame. In warm, dry weather this takes 4-6 hours; in damp conditions it may take a full day. The cloth must be completely dry before removal. As wool dries under tension, the fibres set in their stretched position — this is the entire point of tentering.
12
12
Check tension during drying
Check tension during drying
Return to the frame periodically during drying. As the wool shrinks slightly while drying, some sections may loosen. Rehook or adjust any spots where the cloth has gone slack. Consistent tension throughout the drying process produces the most uniform result.
13
13
Test for dryness
Test for dryness
Press the back of your hand against the cloth. Dry wool feels warm to the touch; damp wool feels cool. Check several places — the centre dries last. Do not remove the cloth until it is thoroughly dry across its entire surface.
14
14
Unhook the lower rail
Unhook the lower rail
When fully dry, unhook the cloth from the lower rail first. Work from one end to the other, lifting the selvedge off each tenterhook. Support the freed cloth to prevent it falling onto muddy ground.
15
15
Unhook the upper rail
Unhook the upper rail
Unhook the upper selvedge from the upper rail, again working from one end. As you free each section, drape the cloth over your arm or have an assistant hold it.
16
16
Measure the finished width
Measure the finished width
Lay the cloth flat and measure its width at several points along its length. The width should be uniform and match the target measurement. A well-tentered cloth holds its dimensions — this is the quality that guild inspectors checked and stamped.
الأدوات المطلوبة:
Measuring Tape 3m17
17
Check the grain
Check the grain
Examine the grain of the cloth — the warp and weft threads should cross at right angles. Pull a thread from the cut edge and check it runs straight across the full width. A straight grain means the cloth will drape properly and pieces cut from it will not skew.
18
18
Fold and store the tentered cloth
Fold and store the tentered cloth
Fold the finished cloth lengthwise, then roll it loosely around a wooden rod or fold in even layers. The cloth is now ready for the next finishing stage: napping (raising the surface fibres with teasels) followed by shearing, or it may go directly to dyeing if it was fulled in the grease.
المواد
2- 1 قطعةعنصر نائب
- 20 لتراتعنصر نائب
الأدوات المطلوبة
4- عنصر نائب
- عنصر نائب
- عنصر نائب
- عنصر نائب
مواد المخططات المرتبطة
المخططات ذات الصلة
هذه المخططات تشارك المعرفة مع هذا — التقنيات والمواد والمبادئ
Fulling Wool Felt for Hats — Medieval Feltingبواسطة Tex
Carding and Combing Raw Wool for Spinning — Preparing Fleece for the Drop Spindleبواسطة Tex
Setting Up a Warp-Weighted Loom — Vertical Loom Weavingبواسطة Tex
Dyeing Yellow with Weld — The Best Lightfast Plant Yellow in Historyبواسطة Tex
Dyeing Turkey Red with Madder — The Most Important Red Dye in Human Historyبواسطة Tex
CC0 ملكية عامة
هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.
ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.