فنون

الجمال والعناية

حِرَف

الثقافة والتاريخ

ترفيه

البيئة

الطعام والمشروبات

الهندسة العكسية

العلوم

رياضة

التقنية

الأجهزة القابلة للارتداء

Piston-Pump Egg Beater: Pump the Eggs Through a Grate

J. J. Parker, Marietta, Ohio · Public domain (expired patent)

أنشأه

YourGrandma

6. أكتوبر 2026

Piston-Pump Egg Beater: Pump the Eggs Through a Grate

A whisk stirs the eggs; it does not force them through anything. J. J. Parker of Marietta, Ohio, received US 25,038, dated 9 August 1859, for an egg beater and churn combined: a tin tube with square openings at its lower end and a piston inside, worked up and down "in the manner of a pump" by a crank, which "draws the eggs in and out through the grate bars until they are completely torn in pieces or made perfectly fine and frothy"; a band turned round the tube's foot closes the openings to vary the agitation. This rung works out the jet speed at each band setting, then prints the tube, band and piston, fits the crank, and times a beating at two settings.

متوسط

About 3 hours, plus printing

التعليمات

Jet speed at each setting

جارٍ تحميل دفتر Jupyter…

The churning it also does

The embedded blueprint churns cream to butter. Parker's pump-tube does the same when worked longer in cream.

Read US 25,038

"At the lower end of the tube is a band of about one half an inch in width loosely fitted with openings one fourth of an inch square and corresponding exactly with the openings in the tube and of the same size, so that by turning the band around either way the openings are closed or made smaller at pleasure, so as to produce more or less agitation in the eggs or cream. This band has a bottom with grate like bars cut or made in it."

Print the tube, band and piston

Print the tube (/uploads/blueprints/piston-pump-egg-beater-tube.stl), the band with its grate (/uploads/blueprints/piston-pump-egg-beater-band.stl) and the piston disk (/uploads/blueprints/piston-pump-egg-beater-piston.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.

المواد لهذه الخطوة:

خيط PETG1 قطعة

الأدوات المطلوبة:

طابعة ثلاثية الأبعاد بالخيط (FDM)

Pack the piston

Cut a leather disk 2 mm larger than the piston. Clamp it between the printed disk and a washer on an M3 rod end with a nut, so its edge seals the tube.

المواد لهذه الخطوة:

جلد مدبوغ1 قطعة

حلقة تثبيت مسطحة1 قطعة

صامولة سداسية1 قطعة

براغي آلية1 قطعة

الأدوات المطلوبة:

سكين حِرَفية

مفتاح ربط قابل للضبط

قدمة رقمية 6 بوصات

Post and crank

Epoxy a 4 mm wire post up the tube's side, bent at its top into bearings 100 mm above the tube. Bend a crank shaft of 3 mm wire with a 22 mm crank one end and a handle the other, and link the crank to the rod with a wire pitman.

المواد لهذه الخطوة:

قضيب فولاذ طري1 قطعة

سلك من الفولاذ المقاوم للصدأ1 قطعة

إيبوكسي ثنائي المكوّن1 قطعة

الأدوات المطلوبة:

ملزمة منضدة

زرادية مستديرة الفك

كماشة مسطّحة الفكّين

منشار حديد

نظارة أمان شفافة

The patent drawing

US 25,038 drawing sheet, public domain (expired patent).

Beat at two settings

Stand the beater in a bowl with two eggs and a spoon of sugar. Crank twice a second with the band fully open and time to a fine froth; repeat with the band half closed.

المواد لهذه الخطوة:

بيضة4 قطع

سكّر محبّب1 قطعة

الأدوات المطلوبة:

وعاء خلط كبير من فولاذ مقاوم للصدأ

ساعة إيقاف

A pump that leaks past, sticks or splashes

Piston-pump egg beater troubleshooting.

Flow

History and honest limits

**J. J. Parker** of Marietta, Ohio, received US 25,038, dated 9 August 1859. His smaller machine's tube is one and a half inches across and one and five eighths deep; the crank shaft is No. 7 wire with a seven-eighths-inch crank; the piston is two oval pieces of thin metal with leather between, its edges forced out by pressing them together. It may also be worked by a handle on the rod instead of a crank. **Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed PETG stands in for tin. The notebook treats the flow as steady. Your times are the result.