التعاون
فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)
Ed

أنشأه

Ed

28. أكتوبر 2026FI
9
0
0
0
0

Push Button: Normally Open Momentary Switch with a Cushioned Contact (De Reamer, GE 1939)

A panel push button that closes a circuit only while you press it. A spring holds the button out, and a metal rim on the end of its rod sits clear of two contacts. Press it and the rim bridges both contacts. A second spring inside the button lets the rod give, so the contacts never take more than that spring's force. Source: Frank C. De Reamer, US 2,166,803 (General Electric, 1939), Fig. 5. Unknown: the insulating material, the metals and every size. De Reamer gives none of them, so they are linked to unknown heads. The tools are ours. Picture: the patent's Fig. 5.
متقدم
2 days

التعليمات

1

Mould the housing

Mould a cup-shaped housing of insulating material, with a boss on each of two opposite sides, a recess in the top of each boss, a groove inside below each boss, and a bead round the top. Unknown: the material, the sizes and the moulding.

المواد لهذه الخطوة:

مادة عازلة غير معروفةمادة عازلة غير معروفة1 as required

الأدوات المطلوبة:

قالب القولبة بالكبسقالب القولبة بالكبس
أبعاد غير معروفةأبعاد غير معروفة
2

Make the terminals and contacts

Bend two angled metal strips. The upper end of each sits in a boss recess, and the lower end is a solder lug. Fix each upper end to a contact that fits the groove inside the housing, stepped at its bottom end. Unknown: the metal.

المواد لهذه الخطوة:

معدن غير معروفمعدن غير معروف1 as required

الأدوات المطلوبة:

مقصّ صفائحمقصّ صفائح
كماشة مسطّحة الفكّينكماشة مسطّحة الفكّين
أبعاد غير معروفةأبعاد غير معروفة
3

Make the sleeve, plate and cover

Turn a threaded sleeve and cut its thread. Spin its lower end over onto a metal plate with tangs. Cut a cover of insulating sheet with ears that reach over the bosses and a hole in the middle to guide the rod.

المواد لهذه الخطوة:

معدن غير معروفمعدن غير معروف1 as required
مادة عازلة غير معروفةمادة عازلة غير معروفة1 as required

الأدوات المطلوبة:

مخرطة معادنمخرطة معادن
طقم أدوات المخرطة (HSS)طقم أدوات المخرطة (HSS)
حامل لقمة اللولبةحامل لقمة اللولبة
مقصّ صفائحمقصّ صفائح
قدمة ورنيةقدمة ورنية
أبعاد غير معروفةأبعاد غير معروفة
4

Make the push button

Make a drawn metal tube closed at the top, and a rod with a head. Put a small coil spring in the top of the tube, then the rod's head. Wedge a washer into the tube under the head. Leave clearance so the rod can swivel a little. Turn the rod's lower end down to a smaller diameter. Unknown: the metal.

المواد لهذه الخطوة:

معدن غير معروفمعدن غير معروف1 as required
طقم نوابض ضغططقم نوابض ضغط1 spring

الأدوات المطلوبة:

مخرطة معادنمخرطة معادن
طقم أدوات المخرطة (HSS)طقم أدوات المخرطة (HSS)
قدمة ورنيةقدمة ورنية
أبعاد غير معروفةأبعاد غير معروفة
5

Assemble

Set the terminals in their recesses and the contacts in their grooves. Slide the button into the sleeve, with a coil spring round the rod between the cover and the wedged washer. Pass the rod's end through the cover's hole. Put on it a loose insulating washer with a metal rim round its edge. Hammer the rod's end over into a flange. Lay the cover on the housing, so its ears clamp the terminals, and bend the plate's tangs over the bead.

المواد لهذه الخطوة:

مادة عازلة غير معروفةمادة عازلة غير معروفة1 as required
معدن غير معروفمعدن غير معروف1 as required
طقم نوابض ضغططقم نوابض ضغط1 spring

الأدوات المطلوبة:

ملزمة منضدةملزمة منضدة
مطرقة كروية الرأسمطرقة كروية الرأس
كماشة مسطّحة الفكّينكماشة مسطّحة الفكّين
نظارات أماننظارات أمان
6

Mount and wire it

Put the sleeve through a hole in the panel and clamp the panel between two nuts on the thread. Solder the bared wire ends to the two lugs.

المواد لهذه الخطوة:

صامولة سداسيةصامولة سداسية2 pcs
سلك لحامسلك لحام1 as required

الأدوات المطلوبة:

كاوية لحامكاوية لحام
كماشة مسطّحة الفكّينكماشة مسطّحة الفكّين
7

Check it

At rest, the rim sits against the underside of the cover and the circuit is open. Pressed, the rim meets the stepped ends of both contacts and closes it. The checking is ours: the meter reads open, then closed while pressed.

الأدوات المطلوبة:

جهاز قياس متعددجهاز قياس متعدد

المواد

5

الأدوات المطلوبة

13

هذا المخطط يصنع

المخططات ذات الصلة

هذه المخططات تشارك المعرفة مع هذا — التقنيات والمواد والمبادئ

CC0 ملكية عامة

هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.

ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.

النقاش

(0)

تسجيل الدخول للمشاركة في النقاش

جارٍ تحميل التعليقات...