فنون
الجمال والعناية
حِرَف
الثقافة والتاريخ
ترفيه
البيئة
الطعام والمشروبات
المستقبل الأخضر
الهندسة العكسية
العلوم
رياضة
التقنية
الأجهزة القابلة للارتداء
Sewing a LilyPad Button Circuit
Ed

أنشأه

Ed

13. يوليو 2026FI
9
0
0
0
0

Sewing a LilyPad Button Circuit

Add a switch you can sew: a LilyPad button placed in the circuit lights your LED only while it's pressed. Same e-textile rules as before — + to + and - to -, no crossing lines — but now the button sits in the + line, so current flows only when you press it. A press-to-light patch for a bag, badge or costume.

مبتدئ
30 minutes

التعليمات

1

Plan the circuit with a button

Arrange a LilyPad LED, a LilyPad button and a coin-cell battery holder on felt. The button goes in the + line, between the battery's + tab and the LED's + tab, so pressing it completes the circuit.

المواد لهذه الخطوة:

LilyPad LED - 5 pcsLilyPad LED - 5 pcs1 عبوة
LilyPad Button BoardLilyPad Button Board1 قطعة
LilyPad Coin Cell Battery Holder - 20mmLilyPad Coin Cell Battery Holder - 20mm1 قطعة
Wool Felt SheetWool Felt Sheet1 ورقة
2

Sew the positive line through the button

With conductive thread, stitch from the battery + tab to one tab of the button, then knot and cut; start fresh and stitch from the button's other tab to the LED + tab. Loop 3–4 times through each hole for firm contact and trim the tails short.

المواد لهذه الخطوة:

Conductive Thread - 60g (Stainless Steel)Conductive Thread - 60g (Stainless Steel)1 بكرة
Hand Sewing Needles (Assorted, 30-Pack)Hand Sewing Needles (Assorted, 30-Pack)1 عبوة
3

Sew the negative line

With a fresh thread, stitch the LED - tab straight to the battery - tab. Keep this line well away from the + line and the button — anywhere the two conductive paths touch, the circuit shorts.

4

Press to test

Slot in a CR2032 (+ side up). Press the button — the LED lights; release — it goes out. If it stays dark, check that both button tabs are stitched into the line and that no threads are touching across the two sides.

المواد لهذه الخطوة:

CR2032 Coin Cell BatteryCR2032 Coin Cell Battery1 قطعة
5

Secure and use

Seal each knot with a dab of clear nail polish or fabric glue so it can't loosen. Sew the felt onto a bag, badge or costume — you've made a press-to-light patch.

المواد

7
التكلفة الإجمالية المقدرة
$53.00

المخططات ذات الصلة

هذه المخططات تشارك المعرفة مع هذا — التقنيات والمواد والمبادئ

CC0 ملكية عامة

هذا المخطط مُصدر بموجب CC0. يحق لك نسخه وتعديله وتوزيعه واستخدامه لأي غرض، دون طلب إذن.

ادعم الصانع بشراء منتجات عبر مخططه حيث يكسب عمولة الصانع يحددها البائعون، أو أنشئ نسخة جديدة من هذا المخطط وضمّنه كرابط في مخططك لمشاركة الإيرادات.

النقاش

(0)

تسجيل الدخول للمشاركة في النقاش

جارٍ تحميل التعليقات...