การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
5mm LED: Epoxy Lamp with a Reflector-Cup Lead Frame (Kosman, US 3,821,590, 1974)
Ed

สร้างโดย

Ed

3. พฤศจิกายน 2026FI
8
0
0
0
0

5mm LED: Epoxy Lamp with a Reflector-Cup Lead Frame (Kosman, US 3,821,590, 1974)

A round LED indicator lamp about 0.200 in (5 mm) across. A red GaP chip sits on a small pedestal at the focus of a paraboloid reflector cup that is part of the lead frame. A fine wire runs from the chip to the other lead. The whole is moulded in clear or tinted epoxy, with small lenses moulded into the front face to spread the light. Result: an encapsulated LED lamp visible within about ±45°, moulded many at a time on one lead frame. Source: K. J. W. Kosman and L.-P. Boivin (Northern Electric), US 3,821,590 (1974). Unknown: lead and wire metals, die attach and cure. Picture: the patent drawing.
ผู้เชี่ยวชาญ
Unknown

คำแนะนำ

1

Make the lead frame with its reflector

Make a lead frame carrying many lamps. In each, the negative lead ends in a paraboloid reflector cup with a small pedestal at its focus, and the positive lead ends nearby. Not given: the metal, sizes beyond the lamp's 0.200 in diameter.

วัสดุสำหรับขั้นตอนนี้:

โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 lead frame

เครื่องมือที่ต้องใช้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Mount and bond the chip

Mount a light-emitting chip with a P-N junction, for example red GaP:Zn,O, on the pedestal, so the cup makes contact with one side of the junction. Connect the other side by a fine wire to the positive lead. About 0.015 in square is the junction size Kosman gives for best efficiency. Not given: the die attach, the wire metal.

วัสดุสำหรับขั้นตอนนี้:

ชิป LEDชิป LED1 light-emitting chip
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 bond wire

เครื่องมือที่ต้องใช้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Transfer-mould the lamps

Set the bonded lead frame in a mould and transfer-mould clear or tinted thermosetting resin round all the lamps at once, front face down so any flaws fall at the back. The front face carries seven spherical lenses, six in a ring round one, each 0.045 in across with a radius about 0.8 times its width; an inclined edge sends some light out sideways. Ours: bisphenol epoxy (the patent lists epoxy, silicone, polyester or diallyl phthalate). Not given: the mould, the cure.

วัสดุสำหรับขั้นตอนนี้:

เรซินอีพอกซีบิสฟีนอลเรซินอีพอกซีบิสฟีนอล1 capsule resin

เครื่องมือที่ต้องใช้:

เครื่องอัดขึ้นรูปแบบถ่ายโอนเครื่องอัดขึ้นรูปแบบถ่ายโอน
วิธีขึ้นรูปที่ไม่ทราบวิธีขึ้นรูปที่ไม่ทราบ
4

Cut apart and test

Cut the lamps from the lead frame and light each one with current forward through the junction: the face shows seven bright spots in a 0.100 in image, visible up to about 45° off axis. Not given: the current.

เครื่องมือที่ต้องใช้:

แหล่งจ่ายไฟกระแสตรงแหล่งจ่ายไฟกระแสตรง

วัสดุ

3

เครื่องมือที่จำเป็น

4

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...