ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Crosshead Dasher Churn: Dashers Hinged to a Rising Crosshead Slide Their Outer Ends Up Inclined Grooves, Counter-Dashers Above
Harry Abbott of North Huron, New York, received US 28,723, dated 19 June 1860, for a churn. In a long box a cross-head in the middle is raised and lowered by a lever; a frame dasher of rods is hinged to each side of it, its outer end sliding in a groove in the box's sides that slopes up inward, so the dashers' inner ends rise and fall while their outer ends move in and out. Above each, a dasher hinged to the box's end works against it and keeps the cream from splashing up.
The patent gives no sizes; every size here is ours.
ขั้นสูง
About 3 days
คำแนะนำ
1
1
Inner ends up and down, outer ends in and out
Inner ends up and down, outer ends in and out
กำลังโหลดสมุด Jupyter…
2
2
A hinged dasher in a long box, four months before
A hinged dasher in a long box, four months before
Cunningham swings one dasher from one end. Abbott lifts two from the middle and guides their outer ends in grooves.
3
3
Read US 28,723
Read US 28,723
"Arranged thus, the lower dashers E, E, have a compound motion; the inner ends being raised and lowered nearly vertically, while the outer ends are guided in and out nearly horizontally. The milk, or cream, passing through the rods g, g, of the dashers E, E, is violently and effectively agitated; while the rods o, o, of the auxiliary dashers, which have opposite and antagonistic motions, being arranged at right angles to the rods g, g, effectively break the currents, and allay the agitation on the surface."
4
4
Body A, legs a and grooves b and i
Body A, legs a and grooves b and i
From 20 mm hardwood board make a box 600 x 260 mm inside and 300 deep, glued and screwed, its inside joints sealed with silicone sealant, on four pine legs 480 mm long. Before assembling, rout in each side a vertical groove b 50 mm wide and 10 deep in the middle, and near each end an inclined groove i 14 mm wide and 10 deep, rising inward at 25 degrees from 45 mm above the floor and running into the groove b's path at its top, so the dashers lift out. Cut a lid with a 24 mm square hole in the middle.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง4 ชิ้น
ไม้สนแปรรูป2 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้40 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เราเตอร์
ไม้โปรแทรกเตอร์
สว่านไร้สาย
ชุดดอกสว่าน
แคลมป์แบบบาร์
ชุดไขควง
ตลับเมตร5
5
Cross-head B and dashers E
Cross-head B and dashers E
Cut a hardwood cross-head 50 x 40 mm, 276 long, its ends fitting the grooves b. For each dasher make a frame of two hardwood side bars 16 x 50 mm, 240 long between pins, and ends f, with five 12 mm stainless rods g across it; fix a 10 mm stainless pin across its outer end, standing out 8 mm each side as the bearings h, and hinge its inner end to the cross-head with a 8 mm stainless pin and split pins, at d.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส4 ชิ้น
กาวไม้1 ชิ้น
สลักผ่า4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)6
6
Auxiliary dashers G
Auxiliary dashers G
Make each auxiliary dasher as a frame 230 mm long with four hardwood rods o, 8 mm thick, along its length, at right angles to the rods g below. Hinge its outer end to the box's end 200 mm up with a staple over a hook, held by a button. Let its middle rod run on past its inner end and through a screw eye on the dasher E's inner end, so G's inner end follows E's.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูห่วง2 ชิ้น
ตะขอและห่วงติดเสื้อผ้า2 ชิ้น
สกรูไม้8 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง7
7
Rod C, lever D and fulcrum c
Rod C, lever D and fulcrum c
Cut a hardwood rod C 24 mm square, 420 long, and fix its foot in the cross-head's middle. Bolt a hardwood link c 90 mm between holes to a block on the outside of one end of the box, near the top. Cut a hardwood lever D, 720 mm long with a handle shaped at one end, and bolt it to the top of rod C and, 360 mm from that pin, to the link's top.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
สลักเกลียวหัวกลม3 ชิ้น
นอตล็อกไนลอน3 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์
สว่านไร้สาย
ชุดดอกสว่าน
ประแจเลื่อน8
8
The build in 3D
The build in 3D
FreeCAD model of this build, one side left off: the cross-head in its middle grooves, the two rod dashers hinged to it with their outer bearings in the inclined grooves, the auxiliary dashers above hinged at the ends, the rod C, the lever D and its swinging fulcrum link.
9
9
Churn
Churn
Pour about 15 litres of heavy cream at about 15 °C, checked with the thermometer, into the box and put on the lid. Work the lever up and down steadily, about 120 mm at the cross-head, timing it. When the butter comes, take off the lid, unhook the auxiliary dashers, lift the cross-head and dashers out by the grooves, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด15 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่10
10
Troubleshooting
Troubleshooting
Crosshead dasher churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Harry Abbott** of North Huron, Wayne County, New York, US 28,723, 19 June 1860 (signed 7 April 1860), "Churn". He claimed the dashers E guided by the vertical and inclined grooves, with the counter-acting dashers G. He gives no sizes and allows any equivalent way of working the cross-head; every size, the groove angle and the stroke here are ours.
วัสดุ
15- 4 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 52 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 15 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
1พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Toggle-Lever Churn: A Crank Crooks and Straightens a Jointed Lever, Rocking a Walking Beam Twice Each Turn
โดย Buttercup
งานไม้
7
0
0
0
0
0

Spring-Pole Cam Churn: A Two-Arc Cam Lifts a Hinged Strip Dasher and a Wooden Spring Pole Drives It Down
โดย Buttercup
งานไม้
4
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

