การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Cane Glue Brush: the Bark Stripped from One End and the Fibres Hammered Loose (Adamson, Amateur Work, 1887)
The fret-cutter's glue brush recommended by D. B. Adamson in Amateur Work (1887): a piece of cane with the hard outer skin cut away at one end and the end hammered until the fibres loosen into a stiff brush, "better than any other" for rubbing glue into wood.
เริ่มต้น
A few minutes
คำแนะนำ
1
1
Read Adamson
Read Adamson
"Nothing is better than a piece of cane beaten out at one end."
2
2
Strip the end
Strip the end
Take a piece of cane (ours: about 15-20 cm) and cut off the hard outer covering for a short distance at one end (ours: about 2 cm).
วัสดุสำหรับขั้นตอนนี้:
หวาย1 ชิ้นเครื่องมือที่ต้องใช้:
มีดคัตเตอร์อเนกประสงค์3
3
Beat out the fibres
Beat out the fibres
Lay the stripped end on a hard surface and hammer it until the fibres loosen into a brush.
เครื่องมือที่ต้องใช้:
ค้อน4
4
Use it
Use it
Warm the glue by standing its can or bottle in a basin of hot water, then rub the glue well into the wood with the brush.
วัสดุสำหรับขั้นตอนนี้:
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
ถัง
กาว5
5
Troubleshooting
Troubleshooting
Cane brush troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
From D. B. Adamson, "Fretsaw Work and Marquetry Cutting" III, **Amateur Work, Illustrated**, vol. VII (1887), p. 230 (checked on the archive.org scan amateurworkillus71887lond). He gives no lengths: those and the knife are ours.
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
