ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Air Blower: a Hand-Cranked Fan Blow-Bellows for a Portable Forge (Hasluck, 1904)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
10
0
0
0
0

Air Blower: a Hand-Cranked Fan Blow-Bellows for a Portable Forge (Hasluck, 1904)

An air blower gives a fire a steady stream of air. Hasluck's Smiths' Work (1904) shows a small one for a home-made forge: a brass box with a four-winged tin fan on an iron spindle, spun fast by a hand wheel pressing on a rubber-covered roller. Unlike old bellows it blows continuously, through an outlet 2 1/2 in wide and 3/4 in deep. The book's drawings carry no sizes for the box, so its size, the sheet thickness and the metals of the wire and the plate are unknown here; the tools are ours. Source: P. N. Hasluck, Smiths' Work (1904), pp. 140-143, Figs. 202-211. Picture: their Figs. 203-204.
ระดับกลาง
Two days

คำแนะนำ

1

Read Hasluck

"When this is all done, turn the handle rapidly; the fan inside will then revolve at a good rate, and a strong draught will be obtained."
2

Cut out the box

Cut the two sides and the bottom of the box from sheet brass, and a piece for the top covering, but do not join them yet. Hasluck gives no sizes for the box (unknown); its outlet is to be 2 1/2 in wide and 3/4 in deep.

วัสดุสำหรับขั้นตอนนี้:

แผ่นทองเหลืองแผ่นทองเหลือง1 sides, bottom and covering

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Make the fan

Make the iron spindle (Figs. 204, 205). Drill two holes in each of its four sides, one at each end, tap them, and screw in pieces of wire about 5/16 in long. Cut four pieces of tin, a little narrower than the box, and punch holes in them to match. Slip each wing over its wires, put a washer over each wire and rivet it over. Five or six wings may be used; then solder pieces of wire between them to stiffen them (Fig. 211).

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กเส้นกลม1 spindle
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 wire
แผ่นเหล็กชุบดีบุกแผ่นเหล็กชุบดีบุก1 four wings
แหวนรองแบนแหวนรองแบน8 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ค้อนย้ำหมุดค้อนย้ำหมุด
หัวแร้งบัดกรีหัวแร้งบัดกรี
4

Fit the spindle and close the box

Screw the brass bearings (Fig. 206), a ring with three spokes and a hole in the middle, to the two sides. Fit the iron spindle in the bearings, screw the sides and bottom together, then screw the covering over the top.

วัสดุสำหรับขั้นตอนนี้:

แผ่นทองเหลืองแผ่นทองเหลือง1 two bearings
สกรูเกลียวมิลสกรูเกลียวมิล1 ชุด

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
5

Fit the hand wheel

The wheel has to be bought. Turn a brass spindle for it (Fig. 207), thread it at each end and fix it with a nut to a plate (Fig. 208); put on the wheel, hold it with a washer and another nut, and fit the knob on rather loosely. Before fixing the wheel, turn a small piece of wood (Fig. 209), put an india-rubber band over it and screw it onto the projecting end of the iron spindle. Fix the wheel so it presses tightly against this roller. Instead, both wheels may be grooved and driven by a band.

วัสดุสำหรับขั้นตอนนี้:

ล้อมือหมุนเหล็กล้อมือหมุนเหล็ก1 ชิ้น
แท่งทองเหลืองแท่งทองเหลือง1 wheel spindle
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 plate
น็อตหกเหลี่ยมน็อตหกเหลี่ยม2 ชิ้น
แหวนรองแบนแหวนรองแบน1 ชิ้น
แผ่นไม้แปรรูปแผ่นไม้แปรรูป1 roller
ยางรัดยางรัด1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
สว่านมือสว่านมือ
6

Fit the nose-piece

Cut the nose-piece from sheet brass to the pattern (Fig. 210) and bend it at right angles along the dotted lines so it fits over the outlet end of the box. Rivet or solder its two edges together, drill it and screw it on. Turn the handle quickly to test the draught.

วัสดุสำหรับขั้นตอนนี้:

แผ่นทองเหลืองแผ่นทองเหลือง1 nose-piece

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
หัวแร้งบัดกรีหัวแร้งบัดกรี
สว่านมือสว่านมือ
แว่นนิรภัยแว่นนิรภัย
7

History and honest limits

Hasluck's "Home-made Portable Forges" chapter offers this fan as a cheaper, steadier alternative to the old leather bellows, costing about half as much. He adds that gun-metal is better than brass for all parts except the covering and nose-piece. The drawings carry no sizes, so the box size, the sheet thickness and the metals of the wing wires and wheel plate are unknown; the tools are ours.

วัสดุ

11

เครื่องมือที่จำเป็น

9

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...