การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Aluminium Oxide Abrasive Grit: Alundum by Jacobs's Process (Stansfield, 1914)
Charlie

สร้างโดย

Charlie

4. พฤศจิกายน 2026DE
10
0
0
0
0

Aluminium Oxide Abrasive Grit: Alundum by Jacobs's Process (Stansfield, 1914)

Alundum, the artificial corundum made at Niagara Falls by the Norton Company: bauxite, calcined to drive off its water, is fused in an electric arc furnace with about 5 per cent carbon, which reduces its iron, silicon and titanium to metal nodules; the fused alumina cools slowly into a hard crystalline mass that is crushed and sized as abrasive grit. Bauxite melts near 2,000 °C and could not be melted commercially without the electric furnace. Source: A. Stansfield, The Electric Furnace, 2nd ed. (1914), pp. 357-358. Picture: the book's Fig. 143, the Higgins alundum furnace.
ขั้นสูง
Unknown

คำแนะนำ

1

Calcine the bauxite

Calcine the bauxite in a rotary kiln to drive off its combined water.

วัสดุสำหรับขั้นตอนนี้:

บอกไซต์บอกไซต์1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาเผาแบบหมุนเตาเผาแบบหมุน
2

Fuse in the arc furnace

Strike arcs between the electrodes and the carbon lining of the furnace bottom, then feed the calcined bauxite, with about 5 per cent carbon, in round the arcs; it melts and in time carries the current between the two arcs. Lower the water-cooled shell as the fused alundum builds up; the lower part solidifies as it fills.

วัสดุสำหรับขั้นตอนนี้:

คาร์บอนคาร์บอน1 about 5 per cent

เครื่องมือที่ต้องใช้:

เตาอาร์กไฟฟ้าเตาอาร์กไฟฟ้า
3

Cool slowly

When the shell is full, lift it with its contents off the base, put another shell in place, and let the alundum cool slowly so it grows into a hard, tough crystalline mass.

เครื่องมือที่ต้องใช้:

เตาอาร์กไฟฟ้าเตาอาร์กไฟฟ้า
4

Crush, separate and size

Break up and crush the mass, separate the nodules of reduced metal mechanically, and size the grains for use as an abrasive.

เครื่องมือที่ต้องใช้:

เครื่องบดหินเครื่องบดหิน
ชุดตะแกรง (ตาไล่ระดับ)ชุดตะแกรง (ตาไล่ระดับ)

วัสดุ

2
  • 1 ชิ้น
    ตัวยึดตำแหน่ง
  • 1 about 5 per cent
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

4

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...