การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)
Woody

สร้างโดย

Woody

4. พฤศจิกายน 2026NO
11
0
0
0
0

Belt Sander: a Lathe-Driven Garnet-Belt Sander (Shop Notes, 1919)

A shop belt sander for dressing wood surfaces: a 6 in garnet-paper belt running over four crowned wooden pulleys, one driven by the lathe, pressed down onto the work with a hand float. Best belt speed about 2,500 ft per minute; leave about 1 in between work and belt. Source: Popular Mechanics Shop Notes for 1919, p. 3235. Picture: the article's drawing.
ระดับกลาง
Unknown

คำแนะนำ

1

Turn the pulleys

Build up four solid wood pulleys 10 in across with 8 in faces and turn them in the lathe with a very slight crown; too much crown harms the belt.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง4 built-up pulleys

เครื่องมือที่ต้องใช้:

เครื่องกลึงไม้เครื่องกลึงไม้
2

Mount the pulleys

Mount one pulley on a firmly held arbor in the lathe and the other three on iron-pipe shafts on a frame (drawing). Turn and file a true journal on each pipe, pour babbitt bushings in the pulleys, and cut oil grooves in the pipe or babbitt. Supporting the shafts on one side lets the belt slip off; supporting both sides is stronger.

วัสดุสำหรับขั้นตอนนี้:

ท่อเหล็ก (ผนังหนา ปลายเกลียว)ท่อเหล็ก (ผนังหนา ปลายเกลียว)3 shafts
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 babbitt bushings
ไม้สนแปรรูปไม้สนแปรรูป1 frame

เครื่องมือที่ต้องใช้:

ตะไบโลหะตะไบโลหะ
กระชอนเจาะรูกระชอนเจาะรู
เลื่อยมือเลื่อยมือ
ค้อนค้อน
3

Make the belt

Cut 6 in garnet paper (No. 1 1/2 for general work) so the ends just meet over the pulleys. Glue the smooth side at the joint, splice it with a strip of cloth about 1 in wide and then one about 3 in wide, cover each side with paper, and clamp between two small boards.

วัสดุสำหรับขั้นตอนนี้:

กระดาษทรายกระดาษทราย1 6 in garnet paper
ผ้าฝ้ายผ้าฝ้าย1 ชิ้น
กาวสัตว์กาวสัตว์1 ชิ้น

เครื่องมือที่ต้องใช้:

แคลมป์ตัวซีแคลมป์ตัวซี
4

Set up and run

Run the belt at about 2,500 ft per minute using the lathe's cone pulley. Set the work about 1 in below the belt on a table or a low sliding platform (two sets of tongue-and-groove joints at right angles), start the machine and press the belt down with a float like a blackboard eraser, or a roller.

วัสดุสำหรับขั้นตอนนี้:

ไม้สนแปรรูปไม้สนแปรรูป1 platform, float

เครื่องมือที่ต้องใช้:

เครื่องกลึงไม้เครื่องกลึงไม้

วัสดุ

7

เครื่องมือที่จำเป็น

6

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...