การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Bismuth: Sweated Out of Native Ore in Inclined Iron Tubes, the Schneeberg Way (Thorpe, 1912)
Charlie

สร้างโดย

Charlie

4. พฤศจิกายน 2026DE
13
0
0
0
0

Bismuth: Sweated Out of Native Ore in Inclined Iron Tubes, the Schneeberg Way (Thorpe, 1912)

The old way of getting bismuth from ore that holds it as the metal: heat the lumps just enough in sloping iron tubes and the bismuth, which melts easily, runs out of the rock into pots under charcoal. It takes 30-60 minutes a charge but gets only about two-thirds of the metal. Not given: the furnace temperature. Source: E. Thorpe, Dictionary of Applied Chemistry vol. I (1912), Bismuth, p. 458. Picture: Thorpe's Fig. 1, the furnace in plan.
ระดับกลาง
30-60 minutes per charge

คำแนะนำ

1

Pick and break the ore

Sort the ore (7-12 % bismuth) by hand from the waste rock as far as possible and break it into pieces the size of a hazel nut.

วัสดุสำหรับขั้นตอนนี้:

แร่บิสมัทธรรมชาติแร่บิสมัทธรรมชาติ1 12 cwt per tube charge

เครื่องมือที่ต้องใช้:

ค้อนค้อน
เครื่องชั่งแท่นอุตสาหกรรมเครื่องชั่งแท่นอุตสาหกรรม
2

Charge the tubes

Load about 12 cwt into each inclined iron tube of the furnace, leaving room to stir from the upper end. Close the upper ends with iron plates and the lower ends with plates pierced with round holes. Under each lower end stand an iron pot holding powdered charcoal, kept gently warm by a small charcoal fire.

วัสดุสำหรับขั้นตอนนี้:

ถ่านไม้ถ่านไม้1 powdered, in the pots and for the pot fire

เครื่องมือที่ต้องใช้:

เตาหลอมแยกบิสมัทเตาหลอมแยกบิสมัท
เบ้าหลอมเหล็กเบ้าหลอมเหล็ก
3

Sweat out the bismuth

Fire the furnace with wood so that the metal flows easily. In about 10 minutes the bismuth begins to run into the pots, where the charcoal covers it from the air. Stir the ore now and then with an iron rod from the upper end; in 30-60 minutes the charge is done. 20 cwt of ore burns about 63 cubic feet of wood.

วัสดุสำหรับขั้นตอนนี้:

ฟืนฟืน1 about 63 cu ft per 20 cwt of ore

เครื่องมือที่ต้องใช้:

เตาหลอมแยกบิสมัทเตาหลอมแยกบิสมัท
เหล็กเส้นกลมเหล็กเส้นกลม
4

Rake out and recharge

Rake the spent ore (bismuth barley) out of the upper end into the tank and refill at once with fresh ore.

เครื่องมือที่ต้องใช้:

คราดเหล็กคราดเหล็ก
เตาหลอมแยกบิสมัทเตาหลอมแยกบิสมัท
5

Cast ingots

Ladle the bismuth from the pots into moulds and cast ingots of 25-50 lb.

เครื่องมือที่ต้องใช้:

เบ้าหลอมเหล็กเบ้าหลอมเหล็ก
กระบวยเทน้ำโลหะกระบวยเทน้ำโลหะ
แบบหล่อแท่งโลหะแบบหล่อแท่งโลหะ

วัสดุ

3
  • ตัวยึดตำแหน่ง
  • 1 powdered, in the pots and for the pot fire
    ตัวยึดตำแหน่ง
  • 1 about 63 cu ft per 20 cwt of ore
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

8

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...