ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)
A home-made boring bar for holes too long for an ordinary boring tool, which would spring. A short, stiff bar runs between the lathe centres, driven by a dog, and carries a hardened tool-steel cutter locked in a cross-hole by a set screw. The work is bolted to the lathe carriage and fed past the turning cutter.
Result: a boring bar, plus the small short-cut bar of Fig. 110.
Source: R. F. Yates, Lathe Work for Beginners (1922), pp. 134-136. Unknown: bar diameter and set-screw size. Picture: Figs. 110-111 of the book.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Turn the bar
Turn the bar
Turn a bar no longer than the job needs; the shorter it is, the less it twists under the cut. Drill both ends for the lathe centres. For short cuts, the small bar of Fig. 110 is 4 to 6 inches long with a round shank and a squared end. Ours: mild steel round bar. Not given: the diameter.
วัสดุสำหรับขั้นตอนนี้:
เหล็กเส้นกลมเหล็กกล้าละมุน1 boring barเครื่องมือที่ต้องใช้:
เครื่องกลึงโลหะ
ขนาดที่ไม่ทราบ2
2
Fit the cutter and set screw
Fit the cutter and set screw
Drill a cross-hole through the bar for the cutter and drill and tap a hole into it for a set screw that locks the cutter. Make the cutter of tool steel, grind its point with proper clearance, and harden it.
วัสดุสำหรับขั้นตอนนี้:
เหล็กเครื่องมือสี่เหลี่ยมจัตุรัส1 cutter
โลหะที่ไม่ทราบ1 set screwเครื่องมือที่ต้องใช้:
สว่านแท่น
ชุดต๊าปและดายทำเกลียว
หินลับแบบหมุน
เตาอบชุบความร้อน
ถังชุบน้ำ3
3
Bore with it
Bore with it
Bolt the work down to the lathe carriage carefully and securely; carriage bolts of several sizes are handy for this. Drive the bar between centres with a dog and feed the carriage. Run very slowly when boring cast iron, and keep the feed light so the bar does not spring.
เครื่องมือที่ต้องใช้:
เครื่องกลึงโลหะ
สลักเกลียวหัวกลมวัสดุ
3- 1 boring barตัวยึดตำแหน่ง
- 1 cutterตัวยึดตำแหน่ง
- 1 set screwตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
8- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

การระบุ 10%
Mild Steel Bar Stock Forged from an Ingot
โดย Forge
ยุคใหม่
48
0
0
0
5
0

การระบุ 10%
Tool-Steel Bar: Crucible Steel Drawn Out at a Cherry-Red Heat
โดย Forge
ช่างตีเหล็ก
36
0
0
0
6
0

การระบุ 10%
Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)
โดย Forge
เครื่องมืองานโลหะ
14
0
0
0
1
0
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
