การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)
A homemade ski staff from The Boy Mechanic, Book 2 (1915): a 4-1/2 ft bamboo pole with a leather wrist loop at the top, a 5 in pine disk 6 in above the tip to stop it sinking in deep snow, and a wire spike set in lead in a hardwood plug for icy ground.
เริ่มต้น
About 3 hours
คำแนะนำ
1
1
His sizes in centimetres
His sizes in centimetres
กำลังโหลดสมุด Jupyter…
2
2
Read The Boy Mechanic, Book 2
Read The Boy Mechanic, Book 2
"A ski staff will greatly assist progress over level stretches and is an aid to the ski runner in preserving his balance."
3
3
Cut the staff and loop
Cut the staff and loop
Cut a bamboo pole 1-1/4 or 1-1/2 in in diameter and 4-1/2 ft long. Shave an old strap thinner, cut it about 1/2 in wide, and fix it as a narrow wrist loop at the top.
วัสดุสำหรับขั้นตอนนี้:
ลำไผ่ยาว1 ชิ้น
หนังทำเครื่องม้า1 ชิ้น
หมุดย้ำทองแดง1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยมือ
มีดตัดหนัง
สว่านมือ
ค้อน
ตลับเมตร4
4
Make and fix the snow disk
Make and fix the snow disk
Cut a disk of well-seasoned white pine or spruce, 1/2 in thick and 5 in in diameter, and coat it with shellac. Bore its centre to pass up the staff about 6 in. Fix it with two pieces of heavy wire: wire A goes through the staff below wire B and at right angles to it, so B must be bent over A. Staple both wires to the disk.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้สน1 ชิ้น
น้ำมันเคลือบเชลแล็ก1 ชิ้น
ลวดเหล็กดัด1 ชิ้น
ลวดตัวยูตอกไม้4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยฉลุ
สว่านมือหมุนพร้อมดอก
สว่านมือ
คีมปากแบน
ค้อน
แปรงทาสีหน้ากว้าง5
5
Set the spike
Set the spike
Plug the lower end with hard wood and bore part way into its centre for a wire spike. Cut slight recesses in the sides of the hole to anchor lead, and pour melted lead round the spike. Sharpen the point, then wind the bamboo with waxed twine or fine wire so it does not split.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
ลวดเหล็กดัด1 ชิ้น
แท่งตะกั่ว1 ชิ้น
เชือกปอกระเจา1 ชิ้น
ขี้ผึ้ง1 ชิ้นเครื่องมือที่ต้องใช้:
สว่านมือ
สิ่ว
ทัพพีโลหะ
หัวพ่นไฟโพรเพน
ตะไบ (ตะไบมือ)
คีมปากแบน6
6
Troubleshooting
Troubleshooting
Ski staff troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "How to Make a Ski Staff", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 51). No contributor is named. He gives no wire gauge or spike length. The tools and metric figures are ours.
วัสดุ
11- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
13- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

