การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Closet Shoe Rack: Wedge-Shaped Pockets on the Wall With a Slatted Bottom for Dirt to Fall Through (Boy Mechanic, 1913)
Woody

สร้างโดย

Woody

13. พฤศจิกายน 2026NO
6
0
0
0
0

Closet Shoe Rack: Wedge-Shaped Pockets on the Wall With a Slatted Bottom for Dirt to Fall Through (Boy Mechanic, 1913)

A shoe rack "that can be placed on the wall in the clothes closet", from The Boy Mechanic (1913): two boards 9 in wide and about 3 ft long, held apart by six wedge-shaped partitions so the pockets open wider at the top, and a slatted bottom that lets the dirt fall through. Sizes are the book's. Contributed to Popular Mechanics by Guy H. Harvey of Mill Valley, California.
เริ่มต้น
About 2 hours

คำแนะนำ

1

The partitions

กำลังโหลดสมุด Jupyter…
2

Read The Boy Mechanic

"Two boards, 9 in. wide and about 3 ft. long, with six partitions between, as shown, will make pockets about 6 in. long. The width of the pockets at the bottom is 2 in. and at the top 5 in."
3

Cut the boards and partitions

Cut two pine boards 9 in wide and about 3 ft long, the back and the front. Cut six partitions as wedges from the notebook, 9 in tall, 2 in deep at the bottom and 5 in at the top.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน1 ชิ้น

เครื่องมือที่ต้องใช้:

ตลับเมตรตลับเมตร
ดินสอดินสอ
ฉากตายฉากตาย
เลื่อยมือเลื่อยมือ
4

Assemble the pockets

Nail the partitions to the back board, square to it, one at each end and the rest spaced about 6 in apart. Nail the front board to their sloping edges, so it leans out and the pockets open wider at the top.

วัสดุสำหรับขั้นตอนนี้:

ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

ค้อนหงอนค้อนหงอน
5

Fit the slatted bottom

Nail strips across the bottom of the pockets with gaps between them, as his Fig. 1, so the dirt from the shoes falls through.

วัสดุสำหรับขั้นตอนนี้:

แถบไม้เนื้อแข็งแถบไม้เนื้อแข็ง1 ชิ้น
ตะปูตะปู1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
ค้อนหงอนค้อนหงอน
6

Hang it

Screw the back board to the wall of the clothes closet (ours), and put a pair of shoes toe-down in each pocket.

วัสดุสำหรับขั้นตอนนี้:

สกรูไม้สกรูไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
ชุดไขควงชุดไขควง
7

Troubleshooting

Shoe rack troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Volume 1**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1913 (Project Gutenberg #12655), "Homemade Shoe Rack", contributed by Guy H. Harvey of Mill Valley, California. The board sizes, pocket sizes and six partitions are the book's; the wood, nails, slat sizes and hanging screws are ours.

วัสดุ

4
  • ตัวยึดตำแหน่ง
  • 2 ชิ้น
    ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • 1 ชิ้น
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

7
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...