การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

สร้างโดย

Tinny

13. พฤศจิกายน 2026US
9
0
0
0
0

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
เริ่มต้น
About 2 hours

คำแนะนำ

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

วัสดุสำหรับขั้นตอนนี้:

ถาดอบพายถาดอบพาย2 ชิ้น
ตะกั่วบัดกรีท่อน้ำแบบไร้ตะกั่วตะกั่วบัดกรีท่อน้ำแบบไร้ตะกั่ว1 ชิ้น
ฟลักซ์ฟลักซ์1 ชิ้น

เครื่องมือที่ต้องใช้:

หัวแร้งไฟฟ้าหัวแร้งไฟฟ้า
ตะไบโลหะตะไบโลหะ
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

วัสดุสำหรับขั้นตอนนี้:

กระป๋องดีบุกกระป๋องดีบุก1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรตัดโลหะงานหนักกรรไกรตัดโลหะงานหนัก
ตะไบโลหะตะไบโลหะ
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

วัสดุสำหรับขั้นตอนนี้:

ตะกั่วบัดกรีท่อน้ำแบบไร้ตะกั่วตะกั่วบัดกรีท่อน้ำแบบไร้ตะกั่ว1 ชิ้น
ฟลักซ์ฟลักซ์1 ชิ้น

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
ตะไบโลหะตะไบโลหะ
หัวแร้งไฟฟ้าหัวแร้งไฟฟ้า
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กดัดลวดเหล็กดัด1 ชิ้น
ตะกั่วบัดกรีท่อน้ำแบบไร้ตะกั่วตะกั่วบัดกรีท่อน้ำแบบไร้ตะกั่ว1 ชิ้น
ฟลักซ์ฟลักซ์1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมปากแบนคีมปากแบน
หัวแร้งไฟฟ้าหัวแร้งไฟฟ้า
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

วัสดุสำหรับขั้นตอนนี้:

สายหนังสายหนัง1 ชิ้น
ตะขอสปริงตะขอสปริง2 ชิ้น

เครื่องมือที่ต้องใช้:

น้ำจืดน้ำจืด
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

วัสดุ

7

เครื่องมือที่จำเป็น

6

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...