การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Leather Punch from an Old Pipe Nipple: Edge Ground Thin, Slug Slot Cut Above (Boy Mechanic, 1915)
A shop-made hollow punch for round holes in leather from The Boy Mechanic, Book 2 (1915): an old pipe nipple of the size you need, one end ground on the outside to a very thin cutting edge, and a small slot a little above it to push the leather slugs out.
เริ่มต้น
Half an hour
คำแนะนำ
1
1
Read the tip
Read the tip
"The cutter end can be ground very thin to prevent an over-cut, while a small slot cut a little above it will allow the removal of the leather slugs."
2
2
Choose the pipe
Choose the pipe
Pick an old pipe nipple whose bore matches the hole you want: pieces of almost any size turn up around a shop. If the piece is long, saw it to a handy length (ours).
วัสดุสำหรับขั้นตอนนี้:
ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 ชิ้นเครื่องมือที่ต้องใช้:
ปากกาจับชิ้นงานหน้าโต๊ะ
เลื่อยตัดเหล็ก3
3
Grind the cutter end
Grind the cutter end
Grind one end on the outside to a long bevel, leaving a very thin edge round the bore, as the hatched section in the sketch shows. Keep turning the pipe so the edge stays even.
เครื่องมือที่ต้องใช้:
เครื่องเจียรตั้งโต๊ะ4
4
Cut the slug slot
Cut the slug slot
A little above the edge, cut a small slot through the wall (the sketch shows a triangle) to push the slugs out. Ours: drill a hole and file it to shape.
เครื่องมือที่ต้องใช้:
ปากกาจับชิ้นงานหน้าโต๊ะ
สว่านแท่น
ตะไบ (ตะไบมือ)
ตะไบเข็ม5
5
Punch
Punch
Ours: lay the leather on end-grain wood, stand the punch upright and strike the top with a mallet. Poke the slugs out through the slot.
เครื่องมือที่ต้องใช้:
ค้อนไม้6
6
Troubleshooting
Troubleshooting
Punch troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "Pipe Used as a Leather Punch", **The Boy Mechanic, Book 2** (Popular Mechanics, 1915), p. 138 (checked on the archive.org scan boymechanicbook200chic2). The note gives no sizes; the way the slot is cut, the length and the striking method are ours.
วัสดุ
1- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้


