ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Brake Cylinder: Piston with Packing Leather, Expander Ring and Release Spring (Westinghouse Air Brake Co., 1901)
Forge

สร้างโดย

Forge

2. พฤศจิกายน 2026NO
17
0
0
0
0

Brake Cylinder: Piston with Packing Leather, Expander Ring and Release Spring (Westinghouse Air Brake Co., 1901)

The air cylinder that puts on a railway car's brakes. Air let into the pressure end drives the piston out, and its push rod works the brake levers. When the air is let out, a release spring pushes the piston back. A cup of leather, held against the wall by a spring ring, stops the air from leaking past the piston. Result: a brake cylinder. In the book's driver-brake example, an 8-inch cylinder fully applied puts 2,500 pounds on its piston. Source: Westinghouse Air Brake Company, Air Brake Instruction Book (1901), pp. 55-57 and 97. Unknown: every size except the 8-inch bore, and the metal of every part except the leather; the book does not give them. Picture: Wikimedia Commons.
ขั้นสูง
1 week

คำแนะนำ

1

Bore the cylinder

Make the cylinder with a pressure end and an open end closed by the non-pressure head. Cut a small groove along the wall, the leakage groove: a slight flow of air into the cylinder then escapes through it to the open end instead of pushing the piston out. Unknown: the metal and the sizes (the book's example is an 8-inch cylinder). Ours: bored on a lathe.

วัสดุสำหรับขั้นตอนนี้:

โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 as required

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ก้านคว้านรูก้านคว้านรู
ชุดเครื่องมือกลึง (HSS)ชุดเครื่องมือกลึง (HSS)
เวอร์เนียคาลิเปอร์เวอร์เนียคาลิเปอร์
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Make piston, follower and heads

Turn the piston with its sleeve, into which the push rod from the brake levers fits, a follower plate, and the non-pressure head. Drill the piston for the studs that hold the follower. Unknown: metal and sizes. Ours: lathe and drill press.

วัสดุสำหรับขั้นตอนนี้:

โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 as required

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ชุดเครื่องมือกลึง (HSS)ชุดเครื่องมือกลึง (HSS)
สว่านแท่นสว่านแท่น
เวอร์เนียคาลิเปอร์เวอร์เนียคาลิเปอร์
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Fit the packing leather

Clamp the packing leather to the piston under the follower plate with studs and nuts; its flange presses against the cylinder wall to keep the air from escaping past the piston. Put the round spring packing expander inside the flange to hold it against the wall. Keep the follower nuts tight. Ours: the leather cut to shape with a knife.

วัสดุสำหรับขั้นตอนนี้:

หนังฟอกหนังฟอก1 as required
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 studs and expander ring
น็อตหกเหลี่ยมน็อตหกเหลี่ยม1 ชุด

เครื่องมือที่ต้องใช้:

มีดคัตเตอร์อเนกประสงค์มีดคัตเตอร์อเนกประสงค์
ประแจเลื่อนประแจเลื่อน
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
4

Assemble with the release spring

Slide the piston into the cylinder, put the release spring behind it and close the cylinder with the non-pressure head, so the spring forces the piston back to release whenever the air pressure is let out of the pressure end. The book's maintenance rule: a light grease in the cylinder, especially at the top and inside the packing leather where the expander rests.

วัสดุสำหรับขั้นตอนนี้:

ชุดสปริงกดชุดสปริงกด1 release spring

เครื่องมือที่ต้องใช้:

ประแจเลื่อนประแจเลื่อน
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ

วัสดุ

4

เครื่องมือที่จำเป็น

8

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...