การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)
A shop brazing and tempering torch: a wall-hung pipe tank of gasoline or kerosene pumped up with a bicycle pump, feeding a 1/8 in pipe whose end is coiled round a short 1 in pipe; the flame heats the coil, the oil turns to gas, and it blasts out through a pinhole cap.
Two burners on a tee give a bigger heat.
Source: Popular Mechanics Shop Notes for 1909, pp. 861-862. Picture: the article's drawing.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Make the tank
Make the tank
Cap both ends of a 2 in pipe 20 in long. Drill three holes in the top cap: one for the rubber tube from a bicycle pump, one for a steam gauge, and one with a screw plug for filling with fuel oil.
วัสดุสำหรับขั้นตอนนี้:
ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 2 in x 20 in
ข้อต่อท่อเกลียว3 two caps, plug
เกจวัดความดัน1 ชิ้น
ท่อยาง1 ชิ้นเครื่องมือที่ต้องใช้:
สว่านมือ
ชุดต๊าปและดายทำเกลียว
ประแจจับท่อ
สูบลมจักรยานแบบตั้งพื้น2
2
Coil the burner
Coil the burner
Drill the bottom cap and connect a 1/8 in pipe D, any length, with a globe valve in it to set and shut off the oil. Fill the last 10 in of the pipe with lead, coil it round a 1 in pipe F 6 in long, and turn the end out to take two elbows and a short nipple; then melt the lead out. Drill a small hole in the centre of a 1/8 in cap and fit it on the end (E) so the hole lines up with the centre of pipe F.
วัสดุสำหรับขั้นตอนนี้:
ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 1/8 in, and 1 in x 6 in
ข้อต่อท่อเกลียว4 two elbows, nipple, 1/8 in cap
วาล์วโกลบ1 ชิ้นเครื่องมือที่ต้องใช้:
ตะกั่ว
กระชอนเจาะรู
เตาตีเหล็ก
สว่านมือ
ประแจจับท่อ3
3
Start the burner
Start the burner
Hang a little cup holding three or four teaspoonfuls of oil just below the coil and light it to heat the coil; then pump up the tank and open the globe valve. For more heat connect two burners on a tee so their blasts meet.
เครื่องมือที่ต้องใช้:
น้ำมันก๊าด
สูบลมจักรยานแบบตั้งพื้นวัสดุ
5- 1 1/8 in, and 1 in x 6 inตัวยึดตำแหน่ง
- 4 two elbows, nipple, 1/8 in capตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
8- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
