การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Clamping Caul: Plain Pine Board Shaped to the Work (Adamson, 1889)
Woody

สร้างโดย

Woody

9. พฤศจิกายน 2026NO
12
0
0
0
0

Clamping Caul: Plain Pine Board Shaped to the Work (Adamson, 1889)

A caul is a board laid over glued work so the clamps press evenly over the whole surface instead of only under their jaws. D. Adamson (1889) uses a piece of good sound pine about 1 in. thick, shaped exactly to fit the surface: flat for a flat panel, convex for a concave one. For veneering he warms it first. Wood can warp or twist, and burns if overheated; a zinc-faced caul (separate blueprint) lasts longer. Source: D. Adamson, "Practical Veneering", Work, 5 October 1889, pp. 453-455.
เริ่มต้น
Unknown

คำแนะนำ

1

Read Adamson

"The caul itself is either wood or metal, either of which must be shaped exactly to fit the surface to be veneered. Thus for a flat panel it must be flat, while for a concave surface it must be convex, and so on. ... For the material nothing is more suitable than good sound pine."
2

Cut the board

Cut a piece of good sound pine about 1 in. thick, large enough to cover the whole surface to be pressed. Thicker is no better, only waste. The length and width are set by the work (not given).

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน1 about 1 in. thick

เครื่องมือที่ต้องใช้:

เลื่อยช่างไม้เลื่อยช่างไม้
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Shape it to the work

Plane the face that meets the work to fit it exactly: flat for a flat panel, convex for a concave surface. A caul that is hollow in the middle presses only at the edges. How it is trued is not given (ours: plane, checked with a straightedge).

เครื่องมือที่ต้องใช้:

กบไสไม้กบไสไม้
บรรทัดเหล็กตรวจความตรงบรรทัดเหล็กตรวจความตรง
4

Use it

Warm the caul (not so hot that it cannot be comfortably handled), lay it over the veneer with a sheet of slightly greased paper between, and screw down the hand-screws evenly until the glue oozes out at the edges. Leave it until the caul is cold, an hour or two.

เครื่องมือที่ต้องใช้:

แคลมป์แคลมป์

วัสดุ

1
  • 1 about 1 in. thick
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

5

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...