การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Clamping Caul: Zinc Plate with a Pine Backing Board (Adamson, 1889)
Woody

สร้างโดย

Woody

9. พฤศจิกายน 2026NO
7
0
0
0
0

Clamping Caul: Zinc Plate with a Pine Backing Board (Adamson, 1889)

A caul spreads clamping pressure evenly over glued work. D. Adamson (1889) prefers zinc for veneering cauls because it lasts longer than wood: a plate 1/8 to 1/4 in. thick (1/8 in. is enough), with a loose backing board of sound pine about 1 in. thick that keeps it flat and holds its heat. Only the zinc is warmed; the pine backing goes on cold. Source: D. Adamson, "Practical Veneering", Work, 5 October 1889, pp. 453-455.
เริ่มต้น
Unknown

คำแนะนำ

1

Read Adamson

"Perhaps as a general thing the zinc is usually preferred of from 1/8 in. to 1/4 in. in thickness, the former being quite sufficient for ordinary purposes. ... Even with a zinc caul a backing of wood is necessary to keep it flat down to the work, and to prevent the heat from dispersing too rapidly."
2

Cut the zinc

Cut a zinc plate 1/8 in. thick (1/8 to 1/4 in. is usual; too thin does not hold the heat, thicker is only waste), large enough to cover the surface to be pressed and lying flat. Length and width are set by the work (not given). How it is cut is not given (ours: tin snips).

วัสดุสำหรับขั้นตอนนี้:

แผ่นสังกะสีแผ่นสังกะสี1 1/8 in.

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
3

Make the backing board

Cut a backing board of good sound pine about 1 in. thick, the size of the zinc, and plane it flat so it keeps the zinc flat down to the work (ours: plane and straightedge).

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน1 about 1 in. thick

เครื่องมือที่ต้องใช้:

เลื่อยช่างไม้เลื่อยช่างไม้
กบไสไม้กบไสไม้
บรรทัดเหล็กตรวจความตรงบรรทัดเหล็กตรวจความตรง
4

Use it

Warm the zinc only (not so hot that it cannot be comfortably handled), lay it over the veneer with a sheet of slightly greased paper between, put the cold pine board on top, and screw down the hand-screws evenly until the glue oozes out at the edges. Leave it until the zinc is cold, an hour or two.

เครื่องมือที่ต้องใช้:

แคลมป์แคลมป์

วัสดุ

2
  • ตัวยึดตำแหน่ง
  • 1 about 1 in. thick
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

6

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...