การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Combination Lock: a Five-Disc Drawer Lock (Boy Mechanic, 1915)
A keyless lock fitted inside a drawer front: five brass discs on a pin, turned by pins from a knob and dial outside. When the notches line up the latch drops; turning back raises it into its keeper.
The combination is changed by moving the pins in the discs.
Source: The Boy Mechanic, Book 2 (1915), p. 169. Picture: Figs. 1-2 of the book.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Cut the five discs
Cut the five discs
Cut five discs of sheet brass about 1/16 in thick and 1 1/2 in across. Drill each for a driving pin 15/32 in from the centre and press the pin in. Notch discs C, D and E for the latch; shape disc B as a cam to lift the latch into its keeper; leave disc A plain with only its pin (Fig. 1).
วัสดุสำหรับขั้นตอนนี้:
แผ่นทองเหลือง1 discs
โลหะที่ไม่ทราบ1 driving pinsเครื่องมือที่ต้องใช้:
วงเวียนปลายแหลมสองขา
กรรไกรตัดแผ่นโลหะ
ตะไบโลหะ
สว่านมือ
ค้อน2
2
Mount the discs
Mount the discs
Inside the drawer front fit a U-shaped metal bracket F carrying a 1/4 in pin G. Thread the discs on it with rubber washers H to M between them so they don't turn too freely. Fix disc A tight on the end of a 1/4 in rod N that passes out through the front.
วัสดุสำหรับขั้นตอนนี้:
แผ่นเหล็ก1 U-bracket F
แท่งเหล็กกลมคาร์บอนต่ำ1 pin G, rod N
วัสดุที่ไม่ทราบ5 rubber washersเครื่องมือที่ต้องใช้:
สว่านมือ
สว่านมือหมุนพร้อมดอก
กรรไกรตัดแผ่นโลหะ3
3
Fit knob, dial and latch
Fit knob, dial and latch
Make the knob of two pieces of wood screwed together with a pointer between them, fit it on rod N with a washer against the drawer. Paste on a paper dial with division marks and numbers. Fit the latch T in a U-shaped metal piece U inside the drawer end so its heel rests on the disc edges, with its keeper above. To find the combination, open the drawer and turn the knob until each notch comes under the latch heel, noting the number under the pointer each time.
วัสดุสำหรับขั้นตอนนี้:
ท่อนไม้เนื้อแข็ง2 knob
โลหะที่ไม่ทราบ1 pointer, latch, keeper
แหวนรองแบน1 ชิ้น
กระดาษ1 dial
แผ่นเหล็ก1 U-piece
สกรูไม้1 ชิ้นเครื่องมือที่ต้องใช้:
ไขควงปากแบน
กรรไกรตัดแผ่นโลหะวัสดุ
9- 1 discsตัวยึดตำแหน่ง
- 1 pointer, latch, keeperตัวยึดตำแหน่ง
- 1 U-pieceตัวยึดตำแหน่ง
- 1 pin G, rod Nตัวยึดตำแหน่ง
- 5 rubber washersตัวยึดตำแหน่ง
- 2 knobตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 dialตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
