การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Hat Pin With a Hat-Coil and a Hair-Coil, Screwed In and Out (Condra, 1906)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
11
0
0
0
0

Hat Pin With a Hat-Coil and a Hair-Coil, Screwed In and Out (Condra, 1906)

Elizabeth S. Condra of Corona, California, received US 814,833, dated 13 March 1906, for a hat pin that will not work itself out of the hat. Two small coils are bent into the pin: a short one at the point that screws through the hat, and a longer one in the middle that screws into the hair. Turned in, it holds; turned the other way, it comes out. We bend it from steel wire with a glass bead for the head. All sizes are ours.
เริ่มต้น
About 1 hour

คำแนะนำ

1

How much wire

กำลังโหลดสมุด Jupyter…
2

Read US 814,833

"The insertion of the pin is accomplished with the least possible manipulation, as the hat-coil 4 is first passed through one side of the hat, then through the hair, and then through the other side of the hat."
3

Cut and straighten the wire

Cut 1.6 mm steel wire to the length from the notebook. Draw it through a fold of cloth between your fingers, or roll it under a flat board, until it is straight.

วัสดุสำหรับขั้นตอนนี้:

ลวดเหล็กลวดเหล็ก1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมตัดลวดปากเฉียงคีมตัดลวดปากเฉียง
ตลับเมตรตลับเมตร
4

Sharpen the point

Hold the wire in the vice and file one end to a long, even point, turning it as you go. Finish on a sharpening stone so it slips through felt and straw without tearing them.

เครื่องมือที่ต้องใช้:

ชุดตะไบเข็มชุดตะไบเข็ม
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
หินลับมีดหินลับมีด
5

Bend the hat-coil

About 6 mm from the point, wind the wire two turns round a 3 mm rod, spacing them about 3 mm apart, like a small corkscrew. Bend the wire on each side back so the point and the rest of the pin run straight along the coil's middle: her "axis in line with the rod".

เครื่องมือที่ต้องใช้:

แท่งเหล็กกลมคาร์บอนต่ำแท่งเหล็กกลมคาร์บอนต่ำ
คีมปากกลมคีมปากกลม
คีมปากแบนคีมปากแบน
6

Bend the hair-coil

At the place the notebook gives, wind five turns the same way round the same rod, in the same direction as the hat-coil, so one turn of the pin drives both. Bend the ends back in line again. Sight along the pin: the straight parts should all lie on one line.

เครื่องมือที่ต้องใช้:

แท่งเหล็กกลมคาร์บอนต่ำแท่งเหล็กกลมคาร์บอนต่ำ
คีมปากกลมคีมปากกลม
คีมปากแบนคีมปากแบน
7

Fit the head

Cut the end square at the finished length and roughen it with sandpaper. Fill the hole of a glass bead with epoxy and push it on, her head or knob 3. It turns the pin and stops it going too far. Leave it to set as the epoxy's label says.

วัสดุสำหรับขั้นตอนนี้:

ลูกปัดแก้วลูกปัดแก้ว1 ชิ้น
อีพ็อกซีสองส่วนอีพ็อกซีสองส่วน1 ชิ้น

เครื่องมือที่ต้องใช้:

คีมตัดลวดปากเฉียงคีมตัดลวดปากเฉียง
กระดาษทรายกระดาษทราย
8

Put it in

Turn the hat-coil through one side of the hat. Push the pin straight across, without turning, until the hat-coil reaches the far side. Then turn it again: one coil goes through the hat and the other into the hair, and the head comes against the hat. To take it out, turn it back the other way and draw it out.
9

Troubleshooting

Coiled hat pin troubleshooting.

Flow

Loading...
10

History and honest limits

**Elizabeth S. Condra** of Corona, California, US 814,833, dated 13 March 1906, filed 22 August 1904. She claimed "a hat-pin comprising a metal rod having one end sharpened to form a tip or point, a head at the other end, the rod being provided with a hat-coil and a hair-coil". She wrote that it will be impossible for it to work itself out of the hat "as so frequently happens with a straight pin". She gives no sizes: the steel wire, the 230 mm length, the coil size and number of turns, the glass bead and the epoxy are ours.

วัสดุ

3

เครื่องมือที่จำเป็น

9

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...