การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Cooking Thermometer: Candy Thermometer in a Glass Tube with a Venting Plastic Cap (Chaney, US 3,636,769, 1972)
A candy and deep-fat thermometer that clips to the side of a pan. A glass thermometer on a printed scale card sits inside a protective glass tube, so it never touches the candy. The top of the tube is closed by a polyethylene cap that seals in normal use but softens when the whole thermometer is heated far too hot, as in an oven, so the air inside escapes instead of bursting the tube.
Result: a pan-side cooking thermometer that cannot explode if overheated.
Source: J. L. Chaney, US 3,636,769 (1972). Unknown: the scale range, sizes and several materials. Picture: the patent drawing.
ระดับกลาง
Unknown
คำแนะนำ
1
1
Mount the thermometer on its scale
Mount the thermometer on its scale
Fasten a glass thermometer tube to a graduated scale card with small fasteners, the bulb at the bottom. The patent's card is marked with cooking points such as soft ball, hard ball, soft crack, hard crack, fish, fowl, potatoes and doughnuts. Fix a disk on top of the card to keep it centred in the outer tube. Not given: the range, the card and fastener materials.
วัสดุสำหรับขั้นตอนนี้:
เทอร์โมมิเตอร์ห้องปฏิบัติการ1 thermometer tube
วัสดุที่ไม่ทราบ1 scale card, disk
โลหะที่ไม่ทราบ1 fastenersเครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ2
2
Enclose it in the protective tube
Enclose it in the protective tube
Slide the card and thermometer into a glass protective tube, open at the top, so the bulb reaches the lower end and touches a metal cap there to pass on the heat. Not given: the tube size, the metal of the end cap, how the cap is joined to the tube.
วัสดุสำหรับขั้นตอนนี้:
หลอดแก้ว1 protective tube
โลหะที่ไม่ทราบ1 end capเครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ3
3
Fit the venting cap
Fit the venting cap
Close the open top with a cup-shaped cap of a thermoplastic such as polyethylene, a friction fit that seals out dirt. Polyethylene softens at about 180 °F and melts near 250 °F: if the thermometer is heated in an oven to 400-550 °F, the air inside would reach 12-14 psi, but the cap distorts first and lets it out. Do not use rubber or a thermosetting plastic, which does not vent. Ours: LDPE.
วัสดุสำหรับขั้นตอนนี้:
เม็ดพลาสติก LDPE1 capเครื่องมือที่ต้องใช้:
ขนาดที่ไม่ทราบ4
4
Fit the pan clip and use it
Fit the pan clip and use it
Slide a spring clip onto the outside of the tube; its spring arm holds the thermometer upright over the edge of the pan. Clip it on with the bulb end in the candy or fat and read the scale; it also serves for deep frying. Ours: spring steel wire.
วัสดุสำหรับขั้นตอนนี้:
ลวดเหล็กสปริง1 clipเครื่องมือที่ต้องใช้:
คีมปากกลมวัสดุ
6- 1 thermometer tubeตัวยึดตำแหน่ง
- 1 scale card, diskตัวยึดตำแหน่ง
- 1 end capตัวยึดตำแหน่ง
- 1 protective tubeตัวยึดตำแหน่ง
- 1 capตัวยึดตำแหน่ง
- 1 clipตัวยึดตำแหน่ง
วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

อันตราย
การระบุ 10%
Liquid-in-Glass Thermometer: Bulb, Fill, Seal and Scale
โดย Penny
งานแก้ว
42
0
0
0
1
0

อันตราย
การระบุ 10%
LDPE Pellets: Ethylene Polymerised at 1500 Atmospheres with a Trace of Oxygen
โดย Charlie
อุตสาหกรรม
15
0
0
0
2
0

การระบุ 10%
Spring Steel Strip and Wire, Hardened and Tempered
โดย Forge
งานโลหะ
48
0
0
0
5
0
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
