ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
13
0
0
0
0

Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders

Aaron S. Cornell of New York received US 26,093, dated 15 November 1859, for what he called a "Double Rotary Crag Churn". Its bottom and cover are two half-cylinders side by side. One wheel and crank turn two shafts the same way; each carries crossed arms (crags), each arm two hollow half-cylinders back to back so it has four cutting edges, and the arms of one shaft pass between those of the other. A tap lets off the buttermilk into a draw with a sieve underneath. The patent gives no sizes; every size here is ours.
ขั้นสูง
About 3 days, plus printing

คำแนะนำ

1

Two cylinders back to back

กำลังโหลดสมุด Jupyter…
2

Two dashers whose paths cross, the same day

Clow's two upright dashers turn opposite ways. Cornell lays his two shafts flat, turns them the same way and lets their arms pass between each other.
3

Read US 26,093

"As these pinions c, c, are both driven by the common wheel b, such pinions and their shafts will have rotary motion in the same direction so that as the arms on one shaft go down, those on the other shaft will pass upward, and the arms or dashers will thus be continually passing each other, giving the most complete and perfect agitation to the milk in the churn."
4

Print the crags i

A set of two arms on a hub 40 mm across and 26 mm long, bored 16.6 mm: each arm two half-pipes back to back, tapering from 26 to 16 mm, reaching 105 mm from the shaft. Print eleven, with supports. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
5

Print the driving wheel b

Spur wheel, 64 teeth, module 3, 15 mm face, with a hub bored 20.6 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Print the pinions c

Spur pinion, 16 teeth, module 3, 15 mm face, with a hub bored 16.6 mm and a cross hole for a pin. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
7

Ends, trough and cover A

Draw two circles 280 mm across, centres 200 mm apart, on 20 mm hardwood and cut two ends to that outline. Rout a rebate on the inside of each to the 243 mm circles for the sheet, bore 16.6 mm at the two centres, and saw each end across through the centres: the lower halves carry the trough, the upper halves the cover. Bend 1.5 mm stainless sheet, 400 mm long and 615 mm round, to the two lower arcs, and screw it into the lower rebates with silicone sealant. Make the cover A the same way on the upper halves, with two short stainless air pipes a. Fit a spigot J at the bottom of one end, where the two arcs meet.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
แผ่นสเตนเลสแผ่นสเตนเลส2 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น
สกรูไม้สกรูไม้40 ชิ้น
ท่อสเตนเลสท่อสเตนเลส1 ชิ้น
ก๊อกทองเหลืองก๊อกทองเหลือง1 ชิ้น

เครื่องมือที่ต้องใช้:

เข็มทิศเข็มทิศ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
เราเตอร์เราเตอร์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
8

Stand f and draw H

Screw four legs 30 x 20 mm, 270 mm long, to the ends, a cross board shaped to cradle the trough, and two rails underneath. Make the draw H a hardwood tray 360 x 300 x 70 mm that slides on the rails, with a sieve l of stainless mesh on a frame inside it.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้24 ชิ้น
ตะแกรงสเตนเลสเกรดอาหารตะแกรงสเตนเลสเกรดอาหาร1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
แคลมป์แบบบาร์แคลมป์แบบบาร์
9

Shafts K, crags and gearing

Cut two 16 mm stainless shafts 495 mm long. Thread six crags on one and five on the other, 70 mm apart, so the five sit midway between the six, and turn each set a quarter turn from the last; pin them. Lay the shafts in the ends' half-holes, hold them with shaft collars, and put the cover on. Pin a pinion on each shaft's geared end, 25 mm outside the end. Bolt a bracket to the end, fix a 20 mm stud in it 66 mm above the shafts, and fit the wheel b on it meshing with both pinions, with a crank and handle.

วัสดุสำหรับขั้นตอนนี้:

แท่งสเตนเลสแท่งสเตนเลส3 ชิ้น
Shaft CollarShaft Collar4 ชิ้น
สลักผ่าสลักผ่า15 ชิ้น
แหวนรองแบนแหวนรองแบน4 ชิ้น
ชุดสลักเกลียวหกเหลี่ยมคละขนาดชุดสลักเกลียวหกเหลี่ยมคละขนาด4 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน4 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ประแจเลื่อนประแจเลื่อน
10

The build in 3D

FreeCAD model of this build, cut through the middle: the twin half-cylinder trough and cover with the air pipes, the two shafts with their crags passing between each other, the wheel and pinions, the tap, and the draw with its sieve on the stand. The shafts were turned through 12 positions.
ไฟล์แบบBLENDCC0 - Free
11

Churn, then strain

Pour about 12 litres of heavy cream at about 15 °C into the trough, checked with the thermometer, and put the cover on. Turn the crank steadily, timing it. When the butter comes, draw off the buttermilk by the tap into the draw; shake the sieve to gather the bits of butter and put them back. Take the butter out, wash it in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด12 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
12

Troubleshooting

Crag churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Aaron S. Cornell** of New York, US 26,093, 15 November 1859, "Rotary Churn". He claimed "the arrangement of the rotating shafts armed with the concave or recessed crags or dashers within the two concave or half cylinder chambers placed back to back". His crags were galvanized iron or metal; ours are printed. His pinions screw on with left-hand threads so that turning the wheel backwards takes them off; ours are pinned. The patent gives no sizes; every size here is ours.

วัสดุ

19

เครื่องมือที่จำเป็น

18

ไฟล์ออกแบบ

4

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...