การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)
Forge

สร้างโดย

Forge

14. พฤศจิกายน 2026NO
10
0
0
0
0

Flat-Bit Tongs and the Tongs Made from Them, down to Crucible Tongs: Welded Reins, Riveted Joint (Edwinson, 1886)

George Edwinson's tong-making lesson from Amateur Work (1886): jaws forged from inch-square iron, reins of 5/8 in. rod scarfed and welded on, the halves riveted with a hot iron pin. The same flat-bit tongs are then reshaped into pincer, hammer and crook-bit tongs, light smith's pliers, and thinned and curved into crucible tongs.
ขั้นสูง
A day at the forge

คำแนะนำ

1

His sizes

กำลังโหลดสมุด Jupyter…
2

Read Edwinson

"Indeed, the man who can turn out a good pair of tongs may be trusted with almost any job in the smithy."
3

Forge the reins

Cut two pieces of 5/8 in. (16 mm) iron rod, each 2 ft (0.6 m) long, with a cold chisel. Bring one end of each to a white welding heat and draw 3-4 in. down to a taper from 5/8 to 1/2 in., rounded for the hand. Upset the other ends at a white heat and scarf them (his figs. 27-28).

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดัดแท่งเหล็กดัด1 ชิ้น

เครื่องมือที่ต้องใช้:

สกัดเย็นสกัดเย็น
เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
4

Forge the jaws

Cut two 6 in. pieces of 1 in. square iron (or one 12 in. bar, worked from each end before cutting, fig. 29). Forge each jaw end 4 in. long, 1 1/4 in. wide and 3/8 in. thick. Flatten the other end to 1/4 in. thick, round it for the joint (fig. 30) and draw it to a slightly rounded taper (fig. 31).

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าละมุนหน้าตัดสี่เหลี่ยมแท่งเหล็กกล้าละมุนหน้าตัดสี่เหลี่ยม1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
5

Punch the joint

Mark the hole with a centre punch, heat, and punch a 3/8 in. hole over the anvil's heel hole with an iron punch tapering 1/4 to 1/2 in. (fig. 35), or a steel punch of 5/8 in. tool steel.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าเครื่องมือแท่งเหล็กกล้าเครื่องมือ1 ชิ้น

เครื่องมือที่ต้องใช้:

เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
6

Weld jaw to rein

Scarf the taper end of each jaw to fit a rein. Heat both to a welding heat in a clear fire, throw on clean fine fresh-water sand and heat until pasty. Tap the scarfs together lightly, return to the fire a moment, and finish the weld. At a red heat forge the square part to blend into the round rein (fig. 32).

วัสดุสำหรับขั้นตอนนี้:

ทรายทราย1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
7

Rivet the joint

Smiths' way: nick a 3/8 in. round iron rod to rivet length, put the halves together, insert the hot end, twist it off, let 1/4 in. stand below, and rivet both sides. (Or make a 3/4 x 3/8 in. button-headed rivet in a 3/8 in. hole in a flat iron.) If the joint locks, reheat jaws and pin to bright red and work them free.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กดัดแท่งเหล็กดัด1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
แผ่นขึ้นหัวตะปูแผ่นขึ้นหัวตะปู
8

Set the jaws

Heat the jaws and set them to the width of the stock to be held. Spring them wider with a piece of cold iron between and a few light blows.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
9

Crucible tongs and other forms

From flat-bit tongs at the fig. 32 stage: lengthen and curve the bits for pincer tongs (angular notches hold round or square bars), more for hammer tongs, bend them sideways for crook-bit tongs. Small flat-bit tongs with lengthened, shaped bits are smith's pliers; thin those out further and curve them like pincers to make crucible tongs for hot crucibles and pots of molten metal. Heavy tongs 2-5 ft long need stouter iron.

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
10

Troubleshooting

Tongs troubleshooting.

Flow

Loading...
11

History and honest limits

From George Edwinson, "Smithing and Forging" III, **Amateur Work, Illustrated**, vol. V (1886), pp. 266-269 (checked on the archive.org scan amateurworkillus05lond). He gives full sizes only for the flat-bit tongs; crucible tong sizes and curvature are left to the work. Metric figures and tools are ours.

วัสดุ

4

เครื่องมือที่จำเป็น

7

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...